Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
Each node has some state which should be saved in case of a power failure and recovered after it.
The problems:
how to detect the power failure?
where to save...
I have some Bluetooth LE v4.2 beacons that I will connect ONLY with known devices that we may call "readers". No consumer with use my beacons, I program them, I install them...
Hello everyone,
I am currently working on porting the InvenSense motion driver 6.12 to nrf52840pdk.
I followed porting guide provided by InvenSense. However, I met the...
First of all, I know the difference between the two roles, and I have also read through docs.
My question is actually limited to the current nordic mesh implementation....
I need a bootloader that I can use for my application that doesn't use a soft device and allows the firmware to be transferred through uart. Going through the forums, I found...
Common situation:
We have flashed dfu bootloader, and firmware uploaded into Flash via DFU. In this situation, DFU settings page contains correct CRC value for existing...
Because if there is, I'm not seeing it. It seems to me that the SDKv14 has asks you where you want your event handler function like this:
Where spi_0_event_handler() is...
HI,
I have been trying to generate the hex files for the mesh sdk (Latest) examples using cmake following the instructions in the documentation.
But the platforms supported...
Hi All,
I am starting an application using nRF51822 beacon kit.
I have some observation regarding current consumption.
1- erase entire flash and power up only, i can...
I'm trying to measure the startup time of the 32 MHz XTAL at the pins XC1 and XC2. Often a microcontroller will indicate in a register that the XTAL and internal PLL are stable...
I wanna use NFC Tag module for OOB authentication in Bluetooth Pairing. I don't wanna use heavy SDK library for it.
Just need simple function which configure NFC to transfer...
I need to achieve the "few uAmps" level of sleep current while running the latest mbed-os 5 on an nRF2832 (inside a u-blox NINA-B1 module). I'm currently seeing ~500 uA in...
Hello,
I'm writing a python script to flash batches of boards with NRF52's.
This is the part of the script that flashes the boards:
I call that function inside a for...
Hi,
I have a problem using Nrf51822 with softdevice S130 2.0.0.
It happens sometimes, not always just a few times, in an unpredictable wat that using the function sd_ble_gatts_value_get...
