Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello ,
I am using 4 nrf52 DK for Mesh
1. how to I configure a Node as Relay
2. How do I capture MESH Packets/ Data from Mesh in Raspberry Pi and send to cloud
hi,
When working with Keil are the NRF_SDH_CLOCK_LF_RC_TEMP_CTIV & NRF_SDH_CLOCK_LF_RC_CTIV compiled as part of the nrf52810_xxaa project?
if not how can I compile...
Hello, is there a way to send messages via the mesh transport/access layer (not using client/server models) but still be Bluetooth SIG compliant? where can I find information...
Hello,
There are a few posts about EasyDMA consuming 1-2mA of current, and I've measured similar currents. In the nRF52832 product specification, this appears to be one...
Hello,
I am running the ble_app_beacon example and want to add battery percentage in the advertising packets, how to do that. And is it possible for ble_app_beacon example...
I had planned on using the nRF52840 I2S peripheral in Nordic Master mode to either produce a 31.25 kHz sampling rate, or a 62.5 kHz sampling rate for my application.
There...
How do I make my phone to auto connect to my nrf51822 device when it is within range ? I dont want to keep having to tap connect on my app. (android and IOS)
I started with the ble_app_template and a preexisting project written with sdk 12.
I have a custom service and 2 characteristics.
The point I am at now is that my DK advertises...
Hi,
I am doing a beacon application. I am advertising sensor data. I am facing issue with advertising.
When I am powering the hardware using usb cable, my device is working...
Hi,
I am trying to interface external flash with the nrf52. I am able to read the device id. After writing to the status - configuration - bank address registers, I am...
I'm finding a good topic for my thesis which come in the next semester. Has TSCH for nRF52DK be implemented on Contiki OS? If not yet, I want to implement this. It is easily...
I try multiple pins set. My pro code is here.
But this is not clear. I want to decrease my code line. Then I tried this.
I want to know where is my mistake?
I am trying to create a TDMA based network with the nRF24LU1+. I understand that nRF51 and nRF52 have the ability to trigger the transmission of a radio packet upon timer...
I'm using an nRF52 (PRX) to communicate with with an nRF24L01+ (PTX) using ESB. As part of a pairing routine they need to switch channel and addresses. I've confirmed that...
