Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
Hello,
Since I am still a little confused, could anyone tell me what S110 and SDK I should use for nRF51822 QFAA? ( infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
i am going to buy nRF51822beacon but i do not know what to buy with it ?
i will buy nRF51 DK but i also want to use a segger programmer with nRF51822beacon.
what confusing...
I was wondering if you could advise me on the best way of adding in BLE functionality to an existing ANT application. Is it simpler to have both transmitting at the same time...
Peripheral receives 4 bytes from central in order to set color of 5 LEDs (1 byte command type + 3 bytes RGB data). There's an iOS app with color picker where user can select...
hi every one.
I need to load softdevice to nRF52 preview DK before execute this app follow it, but i don't know exactly how to do it.
This is my solution:
open...
Hi,
When I reset my nrf51822 beacon firmware using nrfgo, it works just fine. When I try to reset the firmware using jlink, I end up having problems. There are no errors...
Hello, I have downloaded the nRF_MDK_7_2_1, and open \Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001\s110\ble_app_beacon\arm\ble_app_beacon with Keil_v5.
I set IROM1...
Teaching myself the Nordic libraries and API for nRF51 - going smoothly.
Keil uV5 and Dongle and SDK 9.0.0
Wanted to send my own data in the characteristic for HRM service...
The workaround for nRF51822 PAN#73 specifies setting an undocumented register at offset 0x0C0C of the timer peripheral to 1 prior to TASKS_START , and clearing it after TASKS_STOP...
Hi
I am trying to flash a new firmware into my device through DFU via the programming python script.
I use SDK7.2.0, and do:
ipy main.py -f c:\myproject.hex -a XXXXXXXXXXXX...
We are using the Nordic UART service for our product. Should we just use the standard UUID that the Nordic Uart uses or just generate our own for the product?
Thanks
Hi,
I'm working on an embedded system using PAN1026 bluetooth. I want to use the nRF APP to communicate with the bluetooth module. Currently I have:
Setup the...
To support a mix of v2 and v3 chips, I want to use the 7.x SDK. But I'm not sure it's compatible. The matrix at infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
I'm trying to use the nRF52 preview DK from Linux. Could anyone provide the correct JLink commands for flashing both a standalone hex, as well as one with a softdevice?
...
