Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I am trying to get the example examples/ble_peripheral/ble_app_template to work from nRF5_SDK_13.1.0.
nRF52832, s132, pca10040
Much of the code works, but inside peer_manager_init...
The device use SDK9.0,during the using of device,when disconnect the bluetooth of phone system sometimes,the system halted.
So I make an experiment about the probability...
Hello,
I am trying the Thread Cloud COAP Client
<InstallFolder>\examples\thread\experimental\cloud_coap_client
on a NRF52840 PDK. I'm using Thread SDK v0.10...
I have troubles with connection using nrf51822 and android phones:
First I connect and bond the device to the phone and it works ok.
Then I periodically...
Hiya,
Regarding voltage amplitude peak to peak for external high-swing clock HFXO 32MHz, what's supply rails？I don't find out this specification defined in datasheet PS_V1...
My phone is like beacon that transmit service data.
(I checked service data in different phone.)
scandata.png
So, I want to recieve service data, service UUID with...
Hello,
I am really new to the field, I apologise, if things I am saying do not make sense, explanations and corrections appreciated :) I am trying to reach IPv4 internet...
Hello,
I would like to make use of an external ADC that is connected to my nRF52832 through SPI & easyDMA,minimizing the use of the CPU (or without using the CPU).
The...
Hi all,
I am started my project using the softdevice S130 v2.0.1 and the ble_app_uart example(SDK11) on a custom board with the nRF51822. I had to made some changes for...
Hi,
after porting an existing application from version 3.0 of the s132 SD to version 5.0, I experience, that sd_ble_gatts_rw_authorize_reply() returns NRF_ERROR_INVALID_PARAM...
I want to use the SPI in master mode, but the slave just have three lines,the miso and the mosi is the same line,but I don't know how to config the pins? Do the nRF52832 supports...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
I am trying to wrap BLE into a nice c++ class.
For this i am using ble_app_uart example.
I think it was working fine until i was up to clean the helper functions.
After...
