Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
I have a requirement where a handheld device containing a nrf52832 needs to be automatically paired to a switch (another nrf52832 device) when powered on, how can this be...
Hi triying to drive a Relay with Output but have tried every functon in "nrf_gpio.h"
this works with a LED perfectly :
nrf_gpio_pin_toggle(23);
in the main i configure...
I am currently working in the " ble_thread_dyn_mtd_coap_cli" multi protocol example.
Whenever I call printf my program crashes.
I think it has to do with the ble_nus service...
Dear friends,
I am trying to run the PWM in my project. I have:
added the PWM driver successfully (4.0.0-2.alpha, nrf_drv_pwm.c, nrf_drv_pwm.h) ;
set...
I tried porting app from pc10028 to pca20006 by copying the main file from pc10028 ble_app_uart to main file of ble_app_beacon of pca20006.I resolved all the #include related...
hey
I have a nRF51822 eval board and I want to use it as hid keyboard to send some media key
such as vol+/- play/pause, etc. I have used the example code ble_hid_keyboard...
Hi,
I develop a program using arduino primo,
and i want to layout a new pcb board with new nrf52832 chip.
The new chip may not have any bootloader.
What kind of method...
Hi
In our Nordic SDK ble_peripheral projects , It almost support following boards
1. pca10028
2. pca10036
3. pca10040 .
I want to port in pca20006
May I know...
I am porting a C++ project that was using version 6 of the SDK to version 14.2 (big leap, I know). I want to use all the new bells and whistles from the new SDK that makes...
I am using power profiler with nRF52840 SDK. And I have measured the current of the board. But I want to calculate the energy consumption of my program. How can I get the...
hi ：
I want 4 channel PWM output, the following code doesn't work, I want to know where is wrong
#include <stdbool.h>
#include <stdint.h>
#include "nrf.h"
#include...
Hi,
I would like to control gpio pins in micro seconds with timer,
I know that it is very difficult to implement with only timer owing to soft device (interrupt handing...
Hey Dev zone,
I flashed my application onto my Nordic Thingy board (through Onboard Jlink debugger present on nrf52840 dev board), and can see some pretty colors (LEDs...
