Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I've merged the experimental_ble_queued writes sample code into my project and am testing the long write characteristic with nrfConnect from an Android phone. I get no errors...
Hi,
I am trying to figure out the reboot reason on an NRF52 in order to solve it in the best way.
We have a design with a dual supply 3.6V/5V going through a 3V LDO...
Hello,
i have a BLE Peripheral that has a service that we use to simulate UART over BLE. Very similar to the nRF UART. I consider the time to establish a link that allows...
Hi all,
I am trying to save an UART variable I am receiving. My case is very similar to the example Flash Write Example, but I would write few bytes instead of the whole...
Hello!
I have to sample audio signal from a microphone (MAX 9814 adafruit) with the nrf52 board. I use the saadc and then I perform a FFT of the data using the sdk 13 examples...
I implemented my profile based on GLS example. my profile has five services and every services have several characteristics. Pairing with several smartphone work properly...
hi,
I would like to use pwm to output the 1HZ waveform to drive the motor, but when I set the frequency to be 1HZ, I can not find the device and cause 51822 to reset.
This...
Hello, I'm working with the NRF6310 Motherboard and play with it a little with SDK 6.1, but i want to create profiles with the Bluetooth Developer Studio, so I started using...
I download "nRF5_AirFuel_SDK_2.2.0_7b89a57" and use "ptu_app_beacon" development, I am currently using "nrf51822-QFAA" and "nrf51822-QFAC", how do I set up IROM and IRAM?
Hello iam using softdevice 110 and SDK 10.0.0, Iam trying set tx power of nrf51822 using function sd_ble_tx_power_set(), i have tried 0dBm and 4dBm both are giving same RSSI...
wqewqeqwe.PNG I want to program the nrf52 chip using J link Edu -SWD mode. I actually connected the SWDCLK, SDI, and Vtref and GND of Jlink EDU programer to SWDCLK,SDI,3.3V&...
I have written a simple implementation for using the ccm module with mesh. It encrypts and decrypts as it should but when enabled the processor makes a soft reset. It happens...
I have not gone into much details of 51822. while interfacing BLE to any MCU, Is it possible to add interrupt lines from BLE module to MCU to receive interrupts in MCU. Like...
