Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi - In my app, I'm using Bluetooth, the ADC, the TWI, and the SPI. The general idea is to measure lots of things, store the data in SPI NOR FLASH, and occasionally flush...
I'm testing a custom application with the following configuration:
Custom app based on the ble_app_pwr_profiling SDK example.
Using SDK 13.1
S140 SoftDevice s140_nrf52840_5...
Considering that as soon as the connection is established (GAP Peripheral device receives CONNECT_REQ packet) and advertising is over.
Is it possible once the connection...
Can the smart phones or tablets be configured as a peripheral? If yes, why is this not common? Are there any limitations if a tablet/phone is configured as a peripheral device...
Hi!
I'm developing a project with nrf52832 and I'm getting some problems. The micro is only communicating with an accelerometer (MMA8453) and after some time the communication...
Hello,
I am implementing a custom service with several characteristics, one of which is the current temperature. A second characteristic notifies the user if the temperature...
Hello,
I'd like to upgrade nrf51822 QFAC custom board firmware via DFU and change SoftDevice from s110 to s130. Because of larger (than s110) size of s130 I haven't enough...
Hello,
i am using the Visualgdb with sdk v 13.01. i have Nrf52840
i was trying to read the DeviceID of ADXL345
i am using API from this thread
devzone.nordicsemi...
I have used pstorage before but when I add scheduler to my project I face an error in update function of pstorage that in debug I found error_code : NRF_ERROR_NO_MEM .
any...
In short:
Is it possible to connect a nRF51822 s110 peripheral from a central without the need for sending advertising packets (by peripheral)?
If (hopefully) yes...
Hello,
I am trying to create an application that sends a notification from the nrf52 to a smartphone when a sensor reading exceeds a certain value. Would the immediate...
Hi,
I have designed and made a PCB with the nRF51422 chip on it. I am programming the chip externally using the P20 header pins on the nRF51-DK. I am not sure whether the...
What I have to do if I met this ? I round length to fit (len+4-(len % 4)). Is it right ?
if (!(IS_WORD_SIZED(m_start_packet.sd_image_size) &&
IS_WORD_SIZED(m_start_packet...
Hello,
We have problem BLE connecting to the nRF52832, if we use the method gap_init(), the "better" smartphones can connect(those who support BT 4.2). If we skip the gatt_init...
