Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi Nordic
We want to test radio parameter through IQxel . Now,we need a application software to control nrf51822(TX,TX,outpower,channal and so on ) . Can you recommend...
I'm using the example code for simple device/host Gazell in SDK 7.1.0 as my starting point for my application.
My program runs for a second or two, then ends up in the...
Hi
I am new to programing low energy devices. I got a Blend Micro from RedBearLabs. I am using the
nRF Master Control on android to connect to it. I am able to change...
As I create my first 'profile document', it would be nice to read over some examples. My only knowledge of this document comes from nAN-36, section 2.2.2.5 :
A profile...
Hi
in the SDK 7.1 examples, there are examples about how to use the hardware peripherals, and examples on how to use the BTLE stack, but nothing combined.
How do I combine...
Hello, I've started bluetooth development with nRF51 DK since yesterday.
My devlopment platform is KEIL-MDK(v5)
Yesterday, I just tested my board, download the blink...
I have an nrf51 dev board which i can currently connect to an android phone and read data from. I would like this board to be able to scan for other BLE devices and send data...
While attempting to understand why my S120 v 1.0.1 application aborted in:
sd_softdevice_enable(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, assertion_handler);
producing:
ASSERT...
In regard to the following functions
uint32_t sd_nvic_critical_region_enter ( uint8_t * p_is_nested_critical_region )
uint32_t sd_nvic_critical_region_exit ( uint8_t...
Hello, from looking at the GCC linker files I take it that S120 softdevice doesn't support using the full 32KB RAM of the new nrf51422-xxac devices. Is this something that...
Hi, I have written a simple program to calculate the number of retries with nRF24L01+.
On transmitter side, maximum number of allowed retries is set at 1. The transmitter...
Hi all,
I am a beginner with nRF24LE1, when I want to code some examples using GPIOs, I find that it's difficult to understand the PxCON register function. Whether I configure...
I am using the usb port to download an example project to the NRF development kit board, with Keil4. Somehow it keep telling that "No jlink device found", in Keil, the project...
I'm designing my own pcb with a IMU and nRF51422 but i confused,
What's the best choice, LDO, DC-DC or external regulator configuration if I'll use a cell coin?
Someone...
Hi,
We bought new some new nrf51822 beacon boards to get latest revision HW. Then upgraded Keil uVision to latest 5.13 and installed SDK 7.2. However I can't get anything...