Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hello,
In the following code, I have tried to assign a channel to be asychronous so that I can transmit 8 byte acknowledged messages immediately following a button press...
Hi Support team,
I've ported succesfully chibios RTOS on the nrf51422 for month. I've also ported some drivers like I2C - UART - SPI- GPIOS and others... I can play with...
Hi, I have the nrf6310 code in C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\nrf6310\s110 and then i need use this code in the board PCA20006 (Smart beacon).
Do you know how...
hello Nordics,
i am trying to configure 1ms timer along with BLE_STACK is enable
and same time i am sending 3byte data for every 500ms . and 1ms timer is very important...
I need to automate OTA updating the bootloader and radio for several hundred units that have an nRF51 (softdevice 7.1.0) from a VB.NET windows application. I'm able to call...
Hi, I just bough a couple of dongles (nRF51422_xxAA, with 16kB RAM afaik). In Pack installer there is a lot of example for the nRF51 series but all of them are for nRF51522_xxAC...
Hi,
I have a scenario where we may want a peripheral (using S110 softdevice) to switch connections between 2 centrals, depending on whether the centrals are present or...
Hi,
I am using the sofdevice s110. I want to encrypt my manufacturer_data. However , the type of the advertising is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND.
I tried : nrf_ecb_init...
Hi,
I use an NRF51822 eval board.
Recently i buy a module RFD22301. But it is programmed to be used with RFduino.
How I can program it to use the nordic Nrf51822 basic...
hi!,
I am configuring connection interval time is 7.5ms ,
and slave latency is zero.and every connection interval event I am sending 1 packets (and my data lenth is only...
I'm new to nordic. I am using Nordic DK (PCA 10028) and was able to flash the heart rate example on to the board and see it on my iOS device. I'm trying to test the uart sample...
I'm trying to install nordic SDK for Keil 5.13, but this is what the 'install.bat' says when I open it inside the directory containing 'PackInstaller.exe':
Please wait...
Hello,
I am interested in "nRF51 Smart Remote 2". As I have read in Product Brief it supports feature "Voice Command Features". But I couldn't find any information about...
Hello,
I have an application in which the available power is so extremely limited that the hardware cannot do anything else at the same time as conencting to a central...
