Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
I am building a new PCB board for a prototype. It will be used for proximity. It will blink on low battery. It also has a piezo speaker attached to a pin as well. My question...
Hi all. I'm now developing a triangulation solution for indoor robots as a project at my school. I have 4 radios, that I want to communicate with.
One master node send a...
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Attempting to program a softdevice hex file using Keil uVision and an ST-Link V2, I get:
No Algorithm found for: 10001000H - 10001013H
This is in the UICR (User Information...
Hello,
I am thinking about going to eindhoven the 20th of may for the nordic tech tour presentation.
My main interrest is the new v7.0 S110 softdevice which is to be released...
I have used the NRF51822 evaluation kit for a while now to design a product and it performed perfectly up until a few days ago: the onboard segger now fails to connect to...
hi,
i am using a light sensor which is SMBUS serial interface, i tried to interface twi of nrf51822 with the sensor, but i am not able to get acknowledgement from the sensor...
HI,
I'm using sd_app_evt_wait() for getting back to sleep mode between advertisings. I noticed that when I change the voltage in a small interval mode (40 ms between advs...
Hi, If i am running 2Mb radio channels, how many can i have operating in the 2.4Ghz space concurrently?
ALso, what mechanisms can be employed to detect and move frequency...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
Hi,
I'm using Nordic 8001 with Arduino.
I successfully connected to ANCS. The problem is that i need another iOS App that scans for services on my bluetooth device and...
Hi!
My problem is that my code works on the devkit PCA10004(PCB antenna) but not on my own custom board.
The devboard can be connected to and all characteristics can be...
Hello,
i would like to make device which will be dynamically change connection with centrals. It should be connected to the nereast device (with the most power). So I will...
Hi,
I am currently using this example code (pasted below). It is sending the character 'a' every 4 seconds. I can't figure out which part of the code defines the character...
Attached is the schematic of my part configured for low voltage mode.
Very close to page 62 in the nRF51822 product specification document.
I am externally feeding 1.8V...
