Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi all,
I'm designing my own breakout board for nrf51822 and want to use the mbed platform for it. I was able to make the board work with a very simple, blinking-LED program...
Hello,
I am a newbie of Bluetooth development. I have a question that what is the difference between ACI (Application Controller Interface) given in nRF 8001 and HCI (Host...
Hello,
I have one Eval-Kit (v2.2.0) and I had no problems with SDK5.2.0 and demo programs defined in nRF51822 Evaluation Kit User Guide v1.2. Now I have installed SDK6...
Hi,
On a nRF51822 (QFAAG0) with S120 softdevice (using the recent PCA 10001 v2.2.0 board), i'm trying to perform these operations successively:
a simple RSSI scan...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi,
I want to use the AES of 51822 and I have read the nRF51_Reference_manual,I cann't find any demo about AES in SDK.Do you have the demo code about 51822 AES encryption...
Help please! I've been using the nrf51822-EK for several months. Everything has been working well.
I updated my SDK in order to be compatible with S110-SD-v6. Everything...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
am using nrf51822 chip communicating with PIC16fl1509 through uart.the PIC will send the temperatire values through uart to nrf51822. i have a doubt ! will the uart communication...
Hello,
The fact is that I was testing how to OTA update the kit's firmware. I had no problems with the app but when I tried to upload the bootloader.hex includen in the...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
friends :
i assume that the nordic support team can also be considered as friends.
i purchased a nrf51822-mkit, but it seems that it does not qualify for a legitimate...
Hi guys,
I would like to know how to use the softdevice to enable an interrupt when I receive an advertisement packet. Right now I know we have to use
softdevice_ble_evt_handler_set...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
