i have the nrf5833 dk board, i just started programming from quick start and it worked two times and now it does not program at all, programming failed
I'm seeing garbled/malformed UART console output when running apps on the Thingy:91 X. This includes pre-built apps from Nordic and custom apps I build myself.
Here's an...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Hi,
I need to send an audio signal through BLE connection of nRF51822 module, this signal need to quantized and sampled at rate of minimum 8000 sample/second by ADC, i...
I would like a working example of a simple application that uses soft_device (either S110 or S120) plus UART debugging.
I have read many posts in this forum about this topic...
Hi folks,
do you supply a BT Test-SW to set a module with your NRF51822 in different test modes like continuous FH etc. or to change the device to low, mid, high channel...
Hi,
I want to establish a peer-to-peer communication network between 2 nRF51422, such that both the nRF51422 can Transmit as well as Receive data. Is it possible to achieve...
hi,
as we know, the device need to being linked in 1.28s if Advertising types is BLE_GAP_ADV_TYPE_ADV_DIRECT_IND ,but my host can't link device in 1.28s,so i want to link...
Hi,
I try to evaluate DFU using serial but found difficulty. Seeking help here.
I use PCA10028. First, i falsh S110, v8.0 into it.
Then, compile SDK8.0.0\examples...
Hi all!
I want to allow only 1 device to bond at a time. If another device bonding, I want to delete the previously bonded one.
I tried to use dm_device_delete_all() in...
Hi all,
I'm trying to get TWI working on the nRF51 DK but it's not working.
I used the twi_hw_master_sd.c file so softdevice use should not be a problem.
When I debug...
I am using internal ADC to sample 2 (sometimes 3) channels on about 333Hz frequency.
What I do is:
set channel 1 as input (always two-thirds prescaling, VBG reference...
Hi,
I want to debug nrf51822 beacon using DK.I made the necessary connections between dk and beacon.I managed to flash the beacon using nrfgoStudio , but if I want to do...
I have the following code, it's pretty bare in terms of its functionality:
#include <stdint.h>
extern "C"
{
#include "nrf_delay.h"
}
#include "gazell.h"
#include...
I succeeded to made the BLE DFU example of SDK 8(bootloader\pca10028\dual_bank_ble_s110) with softDevice 8 working on PCA10001.
Now I want to try DFU over UART.
I follow...
Hi,
Sorry if these are silly questions but I've tried some searchings and still cannot figure out the answers for the questions below
What is GATT Server Context...
Hi,
I wrote some code that writes to the flash perfectly when BLE is not enabled but when it is enabled, some of the data are correct while others are either missing or...
