hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I am develop a android application with BLE.
My bluetooth device can be searched by bluetooth scanning of android.
And my application can connect with the bluetooth device...
Hi,
My system is
- nRF5340 custom board - Zephyr OS build v2.3.0-rc1-ncs1 - nRF-Connect-SDK v1.2.0
To perform DFU over UART I was told to merge MCUBoot + mcumgr +...
Hi,
I am developing an application that needs to activate a relay on a central device when an event occurs on the peripheral device. The peripheral will always connect to...
Hey, Brand new to this but long time programmer and I sware I have been trying tons of stuff for 4 days straight now and only posting because I am out of options. My goal...
Hello!
I am new to the Nordic chips and for my project .My question is when i apply for the free SES license from license.segger.com/Nordic.cgi ,the The error is shown in...
Hello,
We have a GATT based product. It's using SDK16 and softdevice v7.0.1. It's using secure DFU to upgrade. Now we are developing new firmware based on Mesh 4.0.
We...
Hello, I designed custom board using nRF52832 and SHT20 ambient temperature sensor. Temperature sensor not detected using example sdk TWI scanner. SCL and SDA pins correctly...
Hello,
For our product, we wish to store a custom post-production name (essentially a serial number) in the UICR registers of the nRF52840. We understand that this can...
I am using a code similar to App_uart_C from SDK17.02 - central sending data over uart to another peripheral.
After 30-60 sec, the operation stops probably due to an error...
Dear Fellow developers
I am developing an application where I need several nrf51 USB dongles (S120) attached to a PC, and I need a way to distinguish one dongle from another...
I am integrating PWM into my project which uses SDK_15.2.0.
My config.sh contains:
and I have included nrfx_pwm.c.
Compiling the project I get this error:
Trying...
The project I'm working on is running off of a CR2032 battery. I want to measure the battery voltage while the radio is transmitting to determine when the battery dips down...
Hello,
I am using "pdm sensor" with "NRF 52832". we have PDM Drivers provided by the NRF . I just want to understand how we can connect the data and clock pin with nrf ...
