I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi there...
I am using :
Device :Custom board using nrf52840 (fanstel module BT840)
SDK : nRF5_SDK_17.0.2
SoftDevice : S140 7.2.0
In order to add DFU capability...
Hello,
Any updates on the modem firmware v1.1.3 and v1.3.0 certification status for Verizon? I was told v1.1.3 was supposed to be around Q4 and v1.3.0 was supposed to...
The actual title is too long, the problem is this.
The documentation for s110 says:
Commands to write a buffer to flash
If the SoftDevice is enabled: This call initiates...
Hi All,
I am developing a Zigbee based light controlling product using nrf52840 and nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 SDK.
All functionality and features developed...
Hi,
I run the radio test with our PCBA with SDK17.0.2, but when I want to send "start_tx_modulated_carrier 100", there's no callback response "<info> app: The modulated...
Hi.
I am looking to implement a nRF52840 chip in my 5v battery operated door lock.
Sorry if this is asked before or should be clear from documentation, but I am not...
Hi,
Do you have an example of how to implement a serial console with nrf connect 1.4.99-dev1 with nrf5340_REV1, I tried compiling usb_uart_bridge but got following error...
There are two central sd_* methods for writing to flash - write and erase. The problem is I need to know where I can put my data without trashing something else that is already...
I have two projects exhibiting the same problem.
I have custom board using the nRF52832 and another using the nRF52840. In both cases I am using nRF5 SDK latest version...
Hello,
I would like to have confirmation that the NRF52 will be compatible with my need.
The NRF52 must be able to be connected to a smartphone, while receiving advertising...
I have problems with my custom board.
I developed the firmware with the nrf52832-dk custom and there the firmware runs standalone (with RTT logs on and without) . but now...
I use a nRF52840 Dongle as the Sniffer HW. I use 2 other nRF52840 boards, one is a peripheral (NUS) and the other is a central/peripheral (NUS). The cen/per connects as a...
Hi I have a custom nRF52840 board, and I have a current BLE UART setup. I also want to communicate with a IMU module via serial connection. Can you point me in the direction...
hi,
ncs1.4.0\nrf\samples\bluetooth\peripheral_uart， The LBS service was added, but Advertising faile.
I don't know that I made a mistake in that step. It may be the address...
