Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
just for understanding what soft device do i have to use when i want to build an application wich use observer role and broadcaster role at same time?
Can i use S110...
In our application, we need to save a group of data objects,
how many data objects in a group is dynamic.
also each data object has different sizes,
a few bytes up to 100...
Hi,
I am using nrf51822 custom board.
I'm trying to make intterrupt when a pin is 0 (or 1) and do some calculations while it remains 0.
However I could not manage...
Hello,
I am trying to use SPI on a mbed nRF51822 and am following the documentation suggestion. We've deleted all code except the minimum to try and track down the problem...
Hi,
i want to build an applicaiton with gcc and eclipse setup and S130. I use OSX.
if i don't use the softdevice and run it with the blank linkerscript my blinky code...
Hello,
We are trying to update to Keil uvision 5.11 and unfortunately breaking our teeth on the pack Installer. The Nordic SDK 5.2.0 is installed on the machine but when...
Hi,
I have installed nRF Master Control Panel app on custom board running Android kitkat 4.4.2(ASOP).
But when I run MCP app it gives prompt that 'Device doesn't support...
Hi all,
I develop a central application, which manages multiple peripheral connections. The application often has to stop and start scanning again. In rare cases the function...
Hi,
I'm trying to get the bootloader from SDK v6 running with SoftDevice v7.
I managed to compile it under Eclipse (gcc). I've just removed buttons and LEDs from the code...
I would like someone from Nordic to confirm that the new softdevice release s110_nrf51822_7.0.0 is not suitable for the 128kb versions of the chip (in my case nRF51822 QFABB0...
Hi!
How is the functionality choosen, the nRF51822 has to offer?
Is the SoftDevice (e.g. SD120) an API in C where a specific functionality (e.g. central role listening to...
Is it possible to use nRF51822 Development Kit without nRFgo Starter Kit? What I need - is to be able to connect couple of LEDs and buttons, can this be achieved without buying...
Hello,
after successfully calling sd_softdevice_enable(), I call ble_cscs_init() and that function returns with error code 7, which means NRF_ERROR_INVALID_PARAM. I've tracked...
