Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I am integrating PWM into my project which uses SDK_15.2.0.
My config.sh contains:
and I have included nrfx_pwm.c.
Compiling the project I get this error:
Trying...
The project I'm working on is running off of a CR2032 battery. I want to measure the battery voltage while the radio is transmitting to determine when the battery dips down...
Hello,
I am using "pdm sensor" with "NRF 52832". we have PDM Drivers provided by the NRF . I just want to understand how we can connect the data and clock pin with nrf ...
Dear Members,
I create a loop inside main.c using code example ant_shared channel,
it's merged with ant_plus hrm_rx, but on forever loop, it stopped on 6 loops, it's...
Hello!
A frequent question in the forum is how to enable logging messages.
My question is exactly the opposite: I experience many NRF_LOG_INFO messages from Nordic library...
I'm having some issues with a design I'm developing using the ISP1807 bluetooth SOC (contains nRF52840). Every time I apply power to my device I have to manually reset the...
Dear Members,
How can I display multiple ANT channel ?
It looks like one channel is occupying all the resource (HRM)
How can I manage the time slice between channel...
Hi,
We are building our synthetic sensors using nRF52840 for smart buildings. In some areas we are using it with BLE only, other areas we use it with BLE mesh. When we want...
Hi,
Hope you are well.
I want to send the saadc data with ble to my pc. I used the below code. I am getting the data in the right format but i am loosing some data in...
I am experience some for me strange behavior with UART0 on a nrf52832. Let me explain:
First I initialize the UART using:
APP_UART_FIFO_INIT(...)
with parameters setup...
Hi,
I am using Ozone with nrf52840.
I used this example: wiki.segger.com/Tracing_on_Nordic_Semiconductor_nRF52840
I am able to debug fine. However, I am unable to see...
SDK 16.0 and SDK 17.0 (tried both versions)
nrf52832
Segger Embedded Studio
Windows 10
When Adding an additional ADC the sleep current increases to greater than...
I am currently using SWO to get tracing data from ITM and DWT successfully.
Now I want to use parallel trace for more throughput. For that I use an FPGA, no JTrace or similar...
I have NRF51822 softdevice, STM link v2 for flashing, segger embedded studio and nrf SDK. I have seen some videos on youtube on how to flash nrf softdevice using ST link....
Hi, all.
I'm using nRF52840 pca10056. s140.
I'm communicating with the CO sensor via uart, but there's a problem.
Sensor-side set to send rx steadily, and when debugging...
