hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
I am working on my first BLE project for my employer and have been unable to connect over BLE to our custom board with the nRF52840 processor. To eliminate issues with my...
I received a nRF9160-DK and was looking at working with zephyr/boards/shields/x_nucleo_iks01a3 but my x_nucleo_iks01a3 shield will not plug into the nRF9160-DK (DK) it seems...
I have setup a small thread network (1 FTD Router, 1 Border Router, 2 MTD Dongles) using the Nordic provided RaspPi border router image.
I have been attempting to get Thread...
In my custome PCB design, I am using the CHIP antenna , the same used in nRF 9160 DK, that is P822601 from ethertroncis. Can this antenna work for GPS too? If not can you...
Hello,
I'm currently working on a custom DFU op-code that allows the MCU to send a "pause" op-code, similar to the op-codes found in the DFU protocol.
The steps I've taken...
Hi All
I’m making a few tests on a custom board equipped with a nRF51822-AA device trying to update the firmware with a newest one based on a more recent SDK
The original...
nRF5 SDK version 17.0.2
In usb_dfu_transport_init we have this:
If the nrf_drv_power driver was already initialized, this will return NRF_ERROR_MODULE_ALREADY_INITIALIZED...
The documentation for the sd_ble_gatts_hvx() method states:
This function checks for the relevant Client Characteristic Configuration descriptor value to verify that the...
Using NCS v1.4.99-dev1.
I have no problem using the PWM with a nRF5340PDK but when i tried it on a nRF5340DK, my program was not working correctly.
I have made a simple...
Hi All:
As the topic............Now ,my program is consisted two group,one is the base group,the other is the application group.We often upgrade the application group,so...
Hi
Try to enable reset pin on a 52810 custom board
After defining CONFIG_GPIO_AS_PINRESET in project I ended with UICR registers set to 0 both PSELRESET[0] and PSELRESET...
I have a project with app + SD + BL + Settings page, all merged using the mergehex tool
The mergehex was installed as part of the nrfutil package.
all is well when the...
