I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
I copy static void radio_disable(void) and void radio_tx_carrier(uint8_t txpower, uint8_t mode, uint8_t channel) into my project.
I call radio_tx_carrier(RADIO_TXPOWER_TXPOWER_0dBm...
Hi all,
I have a spurious crash in the softdevice I guess.
It occurs sometimes when the master (an HTC-M8 android phone)
rapidly submits characteristic changes
(acknowledgement...
SDK: V6.0
HW: PCA10001
APP: s110/ble_app_hrs
Question:
If use "twi_master_init()" with "twi_hw_master.c", the current consumption is added 1m
A. But if use with "twi_sw_master...
Hi I am completely new to ARM development world. I have been developing for years for PC.
Now I am working on a Project where we have decided to evaluate nRF51822 chip...
I would like to know if it is possible to use the internal RC oscillator without calibrating every 4s with the softdevice disable. I just want to read a sensor every 2s and...
I'm interested in using BT LE to collect data from a number of serial based devices -- a point-to-multipoint configuration. I'm familiar with the UART examples and have seen...
Hi,
i am searching for infos about my concrete BLE-Sig certification situation but i cannot see the forest because of all the trees :o)
i am currently developing a BLE...
Hi,
I know that a lot of question exists on that subject, but I can't manage to have an accurate battery measure on [Nordic Beacon device] (battery CR1632 3V) ( www.nordicsemi...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
after reading the nAN-36, I tried to write an application for the nRF51822, with the custom Led Service provided with nAN-36.
I take as a base the Nordic HRM application...
