We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello.
I use nrf51822 EK and custom board.
I have to replace the bd address i can not be found in the ble_app_ibeacon_bcs source code.
Is it any way to fix the bd address...
Hi. I'm curious if there's a way to filter devices in the "Discovered Devices" list while scanning with MCP. We have a lot of BLE devices in our office, so the list is fairly...
Hello, I am looking for the way I can use PWM to control duty cycle of connection. I am really novice and my understanding about programming and Bluetooth protocol is really...
I'd like to use the pin sense function as the power switch of my NRF51822 device. That is to say, after the very first power cycle (reset or battery change), the device goes...
Hi everyone,
I am trying to learn nrf51822 using Keil,
I need a very simple program to learn such as:
function bluetoothhandle(value)
{
if(value=="test1")
{
bluetooth_write...
Hi,
I tried to combine BLE HRS & UART together on nrf51822. The service initialization code is
void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;...
Hi,
I am trying to get the PWM example ( github.com/.../nrf51-pwm-library) to work with a Softdevice (S110) that advertises.
There have been several Questions on the...
hi hakon, you told me to do " Try using the variable, for instance by setting "rx_info.rssi = rx_info.rssi;" in the callback and see if that helps." in the question i have...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
Hi, for some reason ADC_IRQHandler is never called for me.
It's fairly simple and a direct copy of the battery sensor example, so not sure what happened here.
is there...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
I am trying to get the proximity example to pair with Windows, but it fails, requesting me to refer to the manufacturer.
I am using gcc in Eclipse on Windows 8.1 desktop...
sd_softdevice_disable before flash_page_erase and flash_word_write ,
after i want set sd_softdevice_enable ,but system is error
how can set sd_softdevice_enable after set...
Hello,
I'm using: nRF51422-QFAA E00 and SDK - nRF51 5.2.0
My problem with ADC is that I stucked when waiting for event - end of conversion.
I used the code from Nordic...
Hi everybody!
I've plugged my NRF51422 as a slave on a STM32 through a SPI bus. I would like to be able to send to the NRF an unknown amount of data. I also need to read...
