Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,
I have a full working ble code form the example provided (keil), but I DO NOT SEE any uart interrupt happening. I can write data to the uart, but I can't see any interrupt...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I am using hw TWI with the s110_nrf51822_6.0 softdevice, nrf51_sdk_v5_2_0
I am using pin 3 scl and pin4 sda of the nrf51[48]22 eval boards.
I am able to drive these pins...
Hi all!
As we know, the funtion Nordic offer to send the ble data is called "sd_ble_gatts_hvx()". But as far as I observe, this funtion just puts the data in the stack...
Hi,
Need to talk between 2 devices using BLE, so for now I have a device with a service and advertising, but now I need the other one to work as central and connect to...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
sorry if this is a stupid question, but i'm fairly new to BLE (nRF8001), and even newer at report descriptors.
I'm trying to send some media keys, just volume up...
Hello,
if i write a new value to a characteristic with the Master Control Panel sometimes i get a HardFault failure. Most of the time all works fine, if i update the values...
I want to send 512 bytes of data over ble through the characteristic value, as maximum length of the characterstic value is 512. When I try to do the transfer more than 20...
HI,
if i want to enable only some component ex RX,TX in soft device and rest want to disable as they consume memory can it be possible?
can anyone please share information...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Might I know any programming guide for nRF51822.
The online documentation seems focus on the API instead.
I would like to know more detail on SFR (special function register...
