Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
I am attempting to build the new alexa_gadget example that is included in the nRF Connect SDK.
Environment information:
Windows 64-bit
nRF Connect v3.6.0
nRF Connect...
Hi everybody,
I think have a problem which involve writing on the external memory of the nrf52840, what I want is when I receive data from the NUS service I want to store...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hi,
The system has an nRF52840 as a BLE USB Dongle plugged to a PC, and connected by BLE to another device (another nRF52840).
I measure the latency time between the...
Hello everyone.
I made my own board with nrf2840 and wanted to use the CC310 module for encryption.
I uploaded an example from the SDK to my board and in the debug I see...
Hi,
I am a newbie to nRF devices. I have different sensors connected to TWI,SPI,ADC etc. and need to send these data to a cellphone through BLE. Does anyone has a sample...
Hello,
I'm starting to investigate using the nRF52833 as part of my design and i wanted to clarify the specification in the datasheet. it states the following:
Does...
Hi,
When upgrading a project from ncs 1.3.0 to 1.4.0, the clock_control_on() call behaves different; It always returns -EPERM. Did the API change?
The call is used as...
Hi everyone,
I want to modify the USBD example.
In the USBD example there's a mouse but I don't have to work with a mouse.
I want to transfer data from ADC to PC. How...
Hi, I am using the Nordic nRF52832, with v15.2 of theSDK, and would like to use "nrf_sdh_freertos_init" to implement multilink. I refer to example "ble_app_multilink_central...
I have beacon (ble_app_beacon) transmitting every 40...50 ms, nRFConnect shows adv interval is ~44 ms, so it receives ~22 msg/sec. My beacon listener gets only 10...12 msg...
Hi,
I have simple test firmware that simply connects to the network and goes into PSM sleep, it works perfectly well on the nRF9160DK but the Thingy 91 is refusing to connect...
This is a really basic question, but please bear with me. This is my first time foraying beyond the world of Arduino! :)
I'm attempting to make an ANT+ bicycle power meter...
I am using nrf52832,I have Defigned "CONFIG_NFCT_PINS_AS_GPIOS"as below。P0.09 is configed as POWER_HOLD pin, P0.10 is configed as buton.
I found that when I download softdevice...
