i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I used the "echo_bot sample and tried to alter it to use UART2 instead of UART0. Aftet changing the code and putting in the needed overlay, the main() program begins to run...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hello nordic team!
Issue:
I am reaching out because one of my nRF9151DK does not seem to have associated character device files created when I plug it into my laptop,...
I have an application that I want to build and run on 5 or 6 target devices including a nRF52840DK, nRF52840 Dongle, and custom boards. There are areas of the code that only...
Is it possible to see LOG_INF() or LOG_ERR() messages from custom board software when the custom board is connected to a nRF52840DK through connector P20? The custom board...
Can't set tx power level using sd_ble_gap_tx_power_set(tx_power) in S130.
Is there something special I must do? I'm trying to use this function to set the power to any...
Hi, I'm having a problem with registering more than one pstorage_handle_t. So far I believed that I can register as many pstorage_handle_t as I want, but the number of these...
Has anyone had success with a J-link ARM v7 with the nRFgo studio (and nRF51822)? I've got one of the older nRFgo moterboard dev kits, and I've been doing well with the included...
Hello,
I am working on a product, which uses the nRF8001 as basis for the Bluetooth communication. The application offers two interfaces, a custom interface and a HID interface...
Hello,
I have a problem with Indicate Characteristic. When I try to send data using sd_ble_gatts_hvx() function, it always sends 20bytes from address 0x00. This is my code...
I am trying to run my program once per second using timer. The timer is initialized as follows:
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE...
I'm trying to figure out how the bonding works in the multilink demo. It seems like the central device only goes through the bonding if the peripheral has the multilink service...
ble_app_uart_s110_pca10028_nuevo.uvprojx
Hi, I´m using a nRF51244 with s110. I program it in nRFgo Studio (s110_nrf51_8.0.0_softdevice.hex)
I try turn on the passkey...
Hi,
I performed an OTA update of my APP. (SD 7.0 and BLE single bank bootloader were flashed).
The update finished without an error and then my application even starts,...
Hi,
I'm developing on a custom nrf51822-based board, and using the s110 softdevice, version 7.0.0. With JLinkGDBServer and the toolchain's gdb, I can debug softdevice-less...
Do you have a BLE SOC chip that can behave as a master and a slave, and also has embedded stack so no host processor is needed. I am looking for a chip that can be used in...
hi,
Inorder to flash the softdevice to evaluation board PCA10024 , i tried using nrfgo studio as mentioned in the user guide.but the nrfgo studio does not show any board...
Dear all,
I am using SDK7.1 with S130 v0.5 alpha. Can I use the DFU example in the SDK6.1 to update my firmware in the chip(nRF51422)? If not, is there any alternative...
I am using S110-based peripheral device which is sending 20byte notifications. Application on my peripheral works fine (testing with MCP gives transfer rate about 15kB/s which...
