Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
int SEGGER_RTT_printf(unsigned BufferIndex, const char * sFormat, ...)
why only BufferIndex=0 can display information on RTT viewer?
How to output different colors to...
Hello I have this code that sends some L2CAP packet to bluetooth device. I want to do the same for BLE device. Could someone please tell what I have to change on that code...
Hi
I use NRF51822_XXAC + s130_nrf51_2.0.0_softdevice + nRF5_SDK_12.3.0_d7731ad, IDE is segger embedded studio 3.40, my program works well when i set optimize level to...
Hi all,
I'm Carles from Nordic and I'm happy to announce that O'Reilly has recently published a new book "Getting Started with Bluetooth Low Energy" of which I am a co...
Dear Nordic Team, Thanks for supporting.
I want to know how to set user MAC address in SDK12.3.0 for nRF52832. I am using ble_app_blinky example. Please support anyone....
Perhaps the following defines added to the beginning would make user specifications a little clearer
#define Default 0
#define Black 1
#define Red 2
#define Green...
Hello,
I'm trying to run my application from Segger Embedded Studio into my custom nRF52840 board but it is not working !
I switched to Jlink commander to get more details...
Hello,
I am migrating a BLE project from SDK 13.1 to SDK 15, and am running into an issue with SPI functionality. I have followed the migration guide for 14.2 to 15, changed...
Part 1: A device that is exposing Mesh Provisioning Service[as a unprovisioned device] or the Mesh Proxy Service [as a provisioned device] could under-utilize the negotiated...
I am using nrf52832 and i want time.
I am using nrf_calendar_example https://github.com/NordicPlayground/nrf5-calendar-example .
My problem is it gives only resolution...
Hello all,
I have noticed that a delay appear periodically when writing SD card for example, I have something that the following code
Unfortunately, I have a jump...
Hello Nordic Team
I am working on nRF52832 MCU, SDK-11. I want to calculate available space so that I can save custom sensors data in chip.
According to datasheet we have...
I am working with nRFx modules and have a few questions about updating parameters. I started my project with an example and modified what I needed. However, I am not sure...
Hello Nordic experts,
I am trying to add an output endpoint to the usbd_hid_generic example in nRF5_SDK_15.0.0_a53641a. I exactly followed the suggestions in
https://devzone...
Hi,
I am using nrf52840 preview DK as a transmitter and try to get rssi by a linux lib. and it works well. and now I want to find advertisement channel number, because the...