The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I am about to develop a Bluetooth Mesh network with the nRF52832.
With the PCA10040, i already able to form a Bluetooth Mesh Network, such that there is one client act...
Does anyone know where I can find a list of which phones/tablets support Data Length Extension (DLE)?
We are finding that many budget phones (e.g. Motorola G6, Samsung Galaxy...
Hi,
I'm using nRF52840 (rev 1.0.0) and Mesh 2.0.1 and SD 15.0.0.
I added FreeRTOS following the example "hrs FreeRTOS".
In FreeRTOS, the source clock (configTICK_SOURCE...
Hi,
I'm trying to use RTC2 as a custom timer using the RTC Driver, initialised as :
nrf_drv_rtc_t erx_timer_rtc = NRF_DRV_RTC_INSTANCE(2);
But when the BSP library or...
Good morning everyone,
I read a lot of threads in the last week on this subject, but so far I was not able to find a solution to the problem.
On a custom board we are...
Is it possible to use both Zigbee & BLE SDKs at same time? Actually we are planning to use NRF52840 for our next project. In which BLE will be used for Smartphone to NRF communication...
Hi there,
I have suitably designed a battery sampling circuit in my prototype configuration, (Vdd = 1.8V, battery swing = 4.2V to 2.9V) using the app note provided at: https...
I am getting the following error when trying to compile port.c
../../../../../Nordic_Semi/nRF5_SDK_14_2/external/freertos/portable/ARM/nrf52/port.c:93:7: error: expected...
Hello,
Is there any sample code which performs only the most basic functions?
Ie. - Sample code in its simplest form which only sets one pin to an output and sets it...
I'm using SDK 15 and soft device S132 6.0. Using nrf Toolbox to update custom firmware, I'm running into a situation where the DFU update fails with an error code 4 when trying...
Hello,
I have been doing research trying to figure out how to program just the nRF52832 chip. I want to program the nRF52832 chip with the Arduino IDE from sandeepmistry...
Hello!
I am using the nRF2740 board with the nRF8001. If I connect all the pins (SPI, RESET, RDYN, GND) except the Vcc pin I still measure 2.5V at the Vcc pin (Connector...
Hello everyone,
In my current application , I am using nRF52832, with the SDK 11.0. I have a problem with the BLE connectivity, which I think is a hardware issue.
With...
I am doing a connectionless system where I am just broadcasting the data. I am showing a loss of about 50% on the receiver missing the data packets. I have tried before to...
Hello,
I configured pin P1.15 as output and with GPIO_PIN_CNF_DRIVE_H0H1 but I only get 1.7V ?
Does "standard drive" means that the pins can't get to 3V ?
Thank...
