Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
We created a custom made board with an nRF52832 and an LIS2DH accelerometer. The board is working fine when it is being powered from a power supply with 3V but when it is...
Developed with SDK 15.0.0. and s132_nrf52_6.0.0_softdevice
After I generate the DFU package, and upload it with nRF Toolbox, it will returns " Upload failed: REMOTE DFU...
SDK 15.0.0, s132_nrf52_6.0.0_softdevice
I have followed the instruction below:
https://devzone.nordicsemi.com/f/nordic-q-a/29067/installing-micro-ecc-issue/115222#115222...
Hello,
Nrf52832 ibeacon broadcast signal is unstable, and the rssi deviation of left and right upper and lower signals before and after the detection of the same distance...
Hello,
I'm working on some LED sequences using the NRFX PWM driver and I can't get the durations I want right.
Let's say that I want a semi-blinking LED (100% - 50% -...
HI
platform:
sdk:15.0.0
52840
\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10040_uart_debug
I want encode(uart) dfu packet not by nrfutil:
(nrfutil...
In my design, I am using a module based on the NRF52832, with a specified LF clock accuracy of +/-250ppm. In my application, I am using v15.0.0 of the SDK with SoftDevice...
hello, we would like to know which development environment Nordic Semi supports/recommends for NRF52832-QFAA-R (except GCC) Is there a special offer from a manufacturer (e...
I'm in the process of scoping out a new project that is in the realm of robotics. It involves one wireless controller that a person would use to turn and drive four wireless...
Hi there,
I have found a similar thread that dates back from a year ago ( https://devzone.nordicsemi.com/f/nordic-q-a/29073/altering-qspi-address-mode ) but I would like...
I created a application that sometimes uses the BLE for 10 seconds. To turn on the BLE I'm using the function
and to turn off the BLE I'm using the function
I already...
Hello!
I'm trying to interface the DHT11 with my DK. I'm coming from Arduino where all I had to do is to drop some library and instantiate an object. Here with the nRF52...
Hello
I compiled the example ble_app_hrs (ble_app_hrs_pca10056_s140) from SDK 15.0 in IAR 8.11.1
I used softdevice included in the SDK15. (s140_nrf52840_5.0.0-1.alpha_softdevice...
Hi All,
Need a help,
To achieve a long RADIO range i.e Gazell(nordic proprietary RF) range, we are using Nrf52832 with SKY66112.
To control the SKY66112 in PA/LNA...
If we are using an external RTC(for example, PCF85063) with a 32.768kHz XTAL, can we rely on the internal RC oscillator on nRF52840 for the power savings in Deep Sleep mode...
