Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
Reference: bbc micro:bit (microbit) board Eagle schematic files
I heard that bbc's micro:bit board is based on Nordic's nRF51822 & build by Nordic Semiconductors
Since...
Using SDK14.2.
I'm trying to optimize the throughput of my ble_nus-based app (I'm getting about 5k/sec right now). I've read elsewhere on this forum that increasing NRF_SDH_BLE_GAP_EVENT_LENGTH...
Hi.
I am trying to program the ble beacon application example that requires the S132 softdevice. I am following the instructions that request the device be erased first...
Hi,
I'm looking for feedback on the feasibility of using Bluetooth Mesh to network Bluetooth modules in a series of adjacent hotel rooms. All the nodes are also relays since...
Hi!
I have a Nordic nrf51822-DK. I'm need send large data to the Android phone (10 mb).
I'm use sample devzone.nordicsemi.com/.../dealing-large-data-packet-s-through-ble...
This may not be the place to ask this question but have to start somewhere.
1. Using an Adafuit BLE Sniffer nRF51822.
2. Ble-sniffer-osx, Version 1.2. 4 (build 28)
3...
According to the answer here , Nordic currently doesn't offer a proxy node implementation.
What would be the best way of getting started to create a proxy node? Are there...
Hi,
My device is peripheral and server and is connected to an (android) phone. I have two related questions:
a) I understand that maximal packet size is obtained by calling...
Hi!
I'm trying to log the flow of communication in the Light Control example of the Mesh SDK. But when I log all the received network messages on a server, I also get a...
Hello
I would like to check coded phy performance
in order to do so I need to achive the following:
1. change to coded phy on default (as I ub\nderstand can by...
I am getting BLE working on an nRF52832, and I am a bit confused as to what I should be setting RADIO->CRCINIT to. I was hoping someone could clear this up, which is more...
Hello
I m trying to measure the current in my development card nrf52DK using the power profiler kits, so i prepared the board by (cut the PCB track shorting solder bridge...
Hello,
I am using the NRF52-DK softdevice 6.0.0 and NRF SDK 15.0. The app is based on on the ble_app_template PCA10040e S112 (The final chip will be a NRF52810 that's why...
I want to flash the program in my custom board. I have flash the program in nrf52832 BLE module via j-link using nrf52832 development board. So, how do i confirm that the...
I use the SDK S110, I hopes in the low power(operation the current 100 uA is following), and then sustains every second bluetooth broadcast and every second computing time...
