I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hi all, i have already posted in another discussion my problem, but i will resume it here briefly:
i have a simple program (similar to the tutorial of the custom service...
Hi! I want to send data from the temperature sensor from the beacon, receive them with the nrf51 and then send them to the PC via USB cable. The nrf51 has to start the connection...
Hi!
Is it possible to scan on a single channel using SoftDevice 132 running on nRF52?
If no such functionality exists, is there some workaround? Like timeslot API for...
Hi All,
Am using NRF52, SDK 11.0.0.2 alpha , I am using HRS free RTOS example. In that I just created two tasks of equal priority. As per Free RTOS two task must switch...
Hi all,
I'm a newby in the Nordic BLE world, I hope I will find some support on this forum about my problem.
I'm working on a project to create a multilink central device...
So I bought a "social retail" beacon device that claims to have 300foot range. After getting it I realized it uses the "iBeacon" standard, which is not compatible with my...
Hi - I wanted to post for the chance it may help others in the future. I'll spare everyone the drama, but I've been stuck on this issue for days and have finally resolved...
Hi. i'm using PCA10028, SDK10.0.0, S130.
I want to check RF characteristics.
nRf51 should make RF Tx continuously.
I think there is example source code for that.
Which...
The function dm_ble_evt_handler has codes like this.
void dm_ble_evt_handler(ble_evt_t * p_ble_evt){ // from device_manager_peripheral.c
switch (p_ble_evt->header...
Hello,
I have develop and app to send BLE Advertisement packet in Android. But what I found out is my device has Android Lollipop but it does not have peripheral mode turned...
I am using the nRF52 Preview board, PCA 10036. I need to provide a high-frequency clock signal to a peripheral. Anything between 1 and 4 MHz will work. However, I don't need...
I currently call nrfjprog twice to flash the softdevice hex and then the app hex separately. But as I am using two nrfjprog calls, I am unable to set --rbp ALL with the second...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
