Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi everyone. For our product, we need to accomplish tests for CE certification, in accordance with regulations EN300328 paragraph 5.4.10. How can we set the softdevice s310...
I try to integrate the ble peripheral uart example and the beaconing mesh example. It build completed. But when i build and debug on nrf52 board. I have some errors about...
Hello, im a beginner in circuit design, and currently i am developing ESB device that should work on batteries.
Device simply represents a nRF24L01+ module, an ATmega48...
Hi,
I am using nordic nrf52832 nRF5_SDK_14.2.0, I use the RTT for debug, I want MCU in low power mode,so I add the following code:
while(1)
{
NRF_POWER->SYSTEMOFF...
There are parallel 8 bits input to nrf52832 GPIO pins,I want to read the data from the pins and writ it to a RAM.how to do read the data in one CPU clock?
As per this document ....
nrf5_SDK_for_Mesh_v1.0.1_src/doc/introduction/mesh_hw_resources.md
The mesh stack uses flash to store the following states:
- Encryption keys...
We modified the ble_app_beacon example to advertise the beacon once a second.
#define NON_CONNECTABLE_ADV_INTERVAL MSEC_TO_UNITS(1000, UNIT_0_625_MS)
As a result of...
Hello all.
Sorry for the nube question, but I am really struggling to try and get my IMU data from my MPU9250, to send constant notifications through BLE using the NRF8001...
When using BLE_GATTS_VLOC_USER I would tend to make the variable pointed to by ble_gatts_attr_t.p_value volatile to reflect the situation that the value can be changed by...
Hello,
I am new to nrf5 mesh. I have setup my system based on Nordic's documentation and was evaluating Serial Example with Interactive Py script.
My setup consists of...
Hi:
I have a project which nrf51822 exchange some data with TI cc2541.There is a serious issue that the nrf51822 is occasionally reset by the watchdog when it communiates...
Hello all
I am trying to get out some debug messages from my custom Firmware (and board) but the log looks like this:
<info> µ“°8$Mø@ñ¨ó¹)F¨: NRF_LOG initialized
...
Hi,
can you please to provide a more information regard power up sequence?
for example:
we would like to use DC2DC (instead LDO) with CR2032 battery.
the PCB have...
Hi all,
I am trying to send a command to the sensor so that the sensor will response with sending something back for acknowledgement, via UART.
Let say, I want to send...