Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi, DevZone,
I am trying connect nRF52480 Preview DK and an Arduino UNO CAN Bus shield.
What I did is:
1) I directly hook CAN Bus shield on the top of nRF52480 Preview...
Hi,
Does anyone know where to download the old SDK versions? I tried to search it in Infocenter, but there I only found the manual documents and API reference, not the SDK...
How slow will an nrf52832 run, using an external crystal, for the purpose of extending battery life? Or am I looking at the wrong processor? I'm looking for a processor for...
Hi everyone!
I'm new to this platform and researching if it's right for my game studio. What I am looking for is a list of boards that have compliance, ideally in the EU...
Hello!
SDK15's DFU with app_scheduler is great!
I am able to Select, Create, and Write an Init Packet. On Execute, however, I get "Flash erase failed (0x3)". What might...
Dear All: My board will reset some time, and i print the register "RESETREAS", and It's value is 8, the PS says it is "cpu lock up detected", Could anyone tell me what will...
Continuous input of audio stream at ATX , but intermittent output audio streams at ARX. why?
how can i use data channal? Once data (three bytes) is sent at ATX,Receive data...
I try to use the SDK 11.0 for my nrf52832 dfu function . But i encountered the error as below:
I am using the ANT_s332_nrf52_5.0.0 .
Any advice . thanks
Building configuration...
Hi all,
I am using SDK14.1.0
Steps of my execution are -
1) My requirement is to make bond when making connection to the android APP. I have done following initialization...
I'm just getting started with the NRF52DK, Mbed and BLE development. I started with the BLE LED demo( https://github.com/ARMmbed/mbed-os-example-ble/tree/master/BLE_LED )...
Hi, we're developing a peripheral (SD 132) which uses whitelist to prevent connection from unwanted devices.
All works fine and when an unlisted device try to connect, it...
I'm running the code as shown in FDS Usage here: http://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v14.2.0/lib_fds_usage.html?cp=4_0_0_3_50_3
The FDS_EVT_INIT...
The short to suspend after last RX is documented in innocenter, but not defined in the nRF5 SDK (rf52840_bitfields.h). Other bit definitions, such as TWIM_SHORTS_LASTTX_SUSPEND...