I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi,
I'm working on a Keyboard&Touchpad project, very similar configuration with Smart Remote 2, so I'm considering to use nRF24LU1+ as receiver's MCU. The receiver will be...
Hi team ,
i am vishal working for VVDN Tech .
we are going to use 10k parts of nRF52840in our project.
so we need step file of that.
Awaiting your soonest response...
Hi,
I am trying ble_app_uart example of SDK 15.
When I do not connect Uart port (TX, RX) to other peripheral, I get fatal error (log via RTT).
```
0> <error> app...
Hello! I am now using nrf52832 sdk14.2 development, as a slave device, need to be bound to the phone, I now want to know the maximum number of allowed bindings and the current...
Hi support team,
I'm using nrf52840 and SDK 15.0. I need to add buttonless dfu service to my application so that my device could be able to upgrade firmware OTA.
However...
When flashing SoftDevice S130 v2.0.1 with nRFGo Studio ( JLinkARM.dll 5.12f ) and softdevice protection enabled, the UICR.CLENR0 is written with value 0x00B00100 (~11M Bytes...
Hi
I would like to create bin file that contains: softdevice, bootloader, maIn application.
To do so i have programmed sofdevice and bootloader via JLink:
r erase loadfile...
Hi,
we are using mesh SDK 2.1.1 over nRF52832. In that, we had developed our custom bootloader, which was based on UART interrupt to receive commands & data from the host...
Hi,
I am running into a problem on PAC10056, please help, pca10065 used to work fine, don't know what caused, I cannot run or debug code on it through SEGGER, I got
...
Steps to reproduce:
1) Set up slave device
Device: nRF52832 SDK: v15.0.0 Soft Device: S132 v6.0 Examples: Any 6lowpan example (including ipv6_medium_ble)
Disable 6lowpan...
When adding two more characteristics to my custom service, I get error #4 which is an out of memory error. The log is working but it does not show the settings for what I...
Hello,
I'm working with SDK 15.0 and Softdevice S132 6.0. I have two nRF52832 boards (the BMD-300 Evaluation Kit and the SparkFun nRF52832 Breakout ).
I am running ble_app_hrs...
I am quite confused about how to go about programming the nRF52840 Dongle. The "programming" page on infocenter says that it can be programmed through the nRF Connect Programmer...
Hi everybody!
I would like to ask the following nRF52840 has the function of preventing current reverse irrigation?
Or what circuit prevents nRF52840 current from flowing...
Hi,
We're designing a BLE module, which is fairly straightforward. The design contains a nRF52832 + SKYWORKS SKY66403-11 FEM. We set the nRF52832 to transmit at -4 dBm and...
Hello,
I'm working on Keil with SDK 15.0 and Softdevice S132 6.0. I'm trying to run the Nordic UART Service example. I have two nRF52832 boards (the BMD-300 Evaluation Kit...
