Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello,
In my project (nRF52, SDK14.2) I have spi data flash connected to the MCU.
I'm trying to use SPI transaction manager library (nrf_spi_mngr) and face few questions...
I don't know how to use nrf52840 dongle as a sniffer. I look at the official routine. It looks like it really doesn't function as a sniffer. Is this what it is. If not, how...
Hello, we are trying to get a new laptop compiling and debugging with an older project. The old project uses SDK5.2 and SoftDevice 6.2.1. When we open it we get the error...
Hi Everyone,
I have problem about debugging program which for my nRF52810 custom board. I am using SEGGER IDE. I changed ses_nrf52810_Vectors.s and system_nrf52810.c files...
Hi!
We'd like to include a battery-powered remote control in our Bluetooth mesh network, i.e. we'll have a need for low power consumption.
In our mesh, devices may opt...
Hello everyone. I'm using an nRF51 with SDK 15 for a 'peripheral beacon example'. For compiling, I'm using segger embebbed studio. I have another bluetooth module(looks like...
Hello, I am trying to fabricate a board based on the Thingy design, including the accelerometer.
I positioned the components, traces, vias and pads following some recommendations...
Hi all,
Currently i am working on multilink Central and peripheral communication, now i want to do two way communication for the single central and multiple peripherals...
I am trying to use the sdk_config.h file from SDK15 to setup a custom board with a nRF52832. The nRF5283 connects to three SPI peripherals. For ease of software development...
Hi. I'm using nRF52832 SDK 13.0.0 as peripheral.
My device can be always connected by any central.
So some centrals may continue to attempt to connect to my device. I...
Hello!
I am developing a bracelet product base on nrf52832. I have a problem with softdevice's power consumption , when softdevice enabled,the power comsuption will rise...
Hello,
I am developing a basic application on the nrf52832. I am using the SDK14.2 and freertos (two very basic task).
I basically have a problem when I set a uint8...
I want to use app timer to get an power saving delay to wait some external chip operation done. So I use an app timer to set a flag when timer expired and in the wait function...
I need to implement UART service in such a way that it should act as both central and peripheral at a time.
I am using nRF52832 board and SDK 15.
I want to know which...
Using
- nRF5_SDK_15.0.0_a53641a
- gcc-arm-none-eabi-6-2017-q2-update 6.3.1
If I enable APP_TIMER_KEEPS_RTC_ACTIVE in the sdk config, setup the app timer with this...
