Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
Hi there,
I was wondering if someone at Nordic could verify something for me. I had a go at modifying the lightswitch example (node_setup.c) in the mesh sdk, to instead...
I've seen many posts asking this question, but with no definitive answer. I've seen latencies for various GPIOs acting as either SPI or TWI, but no baseline interrupt latency...
Has anyone modified the spi_master_using_nrf_spi_master example (or otherwise gotten) the Crystalfontz CFA211TFH 128x64 panel running w/o mods on the nRF52 DK? I have a panel...
Hello,
I captured following data using a Bluetooth dongle for WIN 7 and a Bluetooth keyboard . I also used Wireshark with USBCap driver to capture data going from BT Keyboard...
With my sparkfun 52832 board, when I use the __WFI instruction and I set my device to generate interrupts on P04, the code returns when an interrupt is generated. With the...
We created a custom made board with an nRF52832 and an LIS2DH accelerometer. The board is working fine when it is being powered from a power supply with 3V but when it is...
Developed with SDK 15.0.0. and s132_nrf52_6.0.0_softdevice
After I generate the DFU package, and upload it with nRF Toolbox, it will returns " Upload failed: REMOTE DFU...
SDK 15.0.0, s132_nrf52_6.0.0_softdevice
I have followed the instruction below:
https://devzone.nordicsemi.com/f/nordic-q-a/29067/installing-micro-ecc-issue/115222#115222...
Hello,
Nrf52832 ibeacon broadcast signal is unstable, and the rssi deviation of left and right upper and lower signals before and after the detection of the same distance...
Hello,
I'm working on some LED sequences using the NRFX PWM driver and I can't get the durations I want right.
Let's say that I want a semi-blinking LED (100% - 50% -...
HI
platform:
sdk:15.0.0
52840
\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10040_uart_debug
I want encode(uart) dfu packet not by nrfutil:
(nrfutil...
In my design, I am using a module based on the NRF52832, with a specified LF clock accuracy of +/-250ppm. In my application, I am using v15.0.0 of the SDK with SoftDevice...
hello, we would like to know which development environment Nordic Semi supports/recommends for NRF52832-QFAA-R (except GCC) Is there a special offer from a manufacturer (e...
I'm in the process of scoping out a new project that is in the realm of robotics. It involves one wireless controller that a person would use to turn and drive four wireless...
Hi there,
I have found a similar thread that dates back from a year ago ( https://devzone.nordicsemi.com/f/nordic-q-a/29073/altering-qspi-address-mode ) but I would like...
