I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
Hi,
I'm using nrf_serial 'object' in order to communicate nRF52832 with an external device.
As I work in non-blocking mode I need to verify if there's available space...
Hi,
We are migrating SoftDevice 5.0 -> 6.0.0-6 alpha on sdk 14.2 (s132->s140) in order to be able to evaluate long range. During the migration we stumbled across some problems...
hi all,
I have an issue with hardware in the circuit, which is designed by my self. The PCB has designed a customized
condition:
I have erased full memory and measure...
we want to support the serial bootloader with SDK13, but find that the example is Experimental: Serial Secure DFU Bootloader, can we use it stably? the SDK14/15 don't Experimental...
I am using nrf52832_xxaa and SDK11.
Is there any formula that states the relation between the advertising & scanning parameters(advertising interval, scanning interval,...
I am trying to flash the program into my custom board. and i am successfully flash the program into custom board. I have flashed the blinky code in y custom board. it's works...
Hi everyone,
I would like to know in the ble_app_uart_pca10040 where the Bluetooth antenna is connected on pin planner to be able to change it.
Thanks you for helping...
Hello there,
I have a question related to the ADC of the nRF52832.
I am using it in single-ended mode, 10-bit resolution, 1/5 gain, internal reference 0.6V.
Thus...
Hello,
I am wondering what this "Low Power Event" is.
I am looking through the document but I can't find the place that explains this.
Can somebody point me to the place...
Hi, I followed the tutorial to Debug with Real Time Terminal on Keil.
fatal error: file sdk_config.h not found.
I have followed the tutorial as precisely as I can, maybe...
hi，there
I met an error in Nordic_HRM examples. The error code is GATT_CONN_TERMINATE_LOCAL_HOST.After the connection is established, you can see the service that has...
Good morning everyone,
it is the stupidest question ever, but I was unable to find an answer neither here nor on the segger forums or documentation.
This forum seems...
It's NRF52832 and NRF52810.
The BLE connection process is to establish a physical connection first and then discover the service to obtain the characteristic word information...
Hi,
For my application, I would like to have multiple watchdog timers. I am measuring several sensors (I want one short-term watchdog timer to be fed in this loop, pause...
I am new with nrf52 DK . I was trying to work with SPI code example given in the nordic example folder but its not working . I am trying to transfer the accellero/ gyro data...
