Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hi Support engineer,
I am quite new to Nodicsemi devices, I am going through some getting started tutorials, but I found there is no tutorial based on Segger Embedded Studio...
Hello,
I'm usign nRF52832 with nRF5_SDK v15. I'm using "ble_app_uart" example. I need to know that What is the maximum datarate for "ble_app_uart" example ?
In the...
I have a question with flash writing of nRF 52. Once written, you can not write it for the second time. It will not cause an error, but is there any way? Write the source...
Runtime environment:
1.IC:52840QIAA ；
2.SOFTDEVICE:s140_nrf52840_5.0.0-2.alpha_softdevice.hex
Development:
PWM signals of 10 groups of adjustable frequency and...
I am trying to establish communication using SPIM. when I checked the macro definition of NRFX_SPIM0_ENABLED it's present in apply_old_config.h. I am using nrfx_spim driver...
Hi,
I have two 52832 (both on SDK 14.2, S132 v5.1) talking to each other using a slightly modified UART service to support more than one connection.
I have this strange...
Hello,
yesterday I measured the current of our device and found out that it looks more as a square instead of spikes when no device was connected. Found out that when I...
In my code , i use P0.6, P0.8, P1.9 to control three RGB LED.
when I use nRF5_SDK_13.0.0-1.alpha, all is fine,
but when use nRF5_SDK_15.0.0_a53641a, the issure like below...
Hello,
I'm new to Nordic SDK and I would like to ask you for help with change of
GPIO IN_EVENT to GPIO PORT event implementation. The reason is we are using
revision <...
Hi,
I'm using nRF5 SDK v15.0 with S132 v6.0. I have two questions:
1. I use the ble_app_uart example. We want to use high UART baud rate, so I change it to 1M baud rate...
The project I am working on stores information in SRAM while it waits for the radio to get in range and transmit data.
I want to know if I can put items in SRAM buffer that...
I'm trying to learn the DFU process and how to include it in a project under development using SDK 15 and the nRF52 DK. I programmed the DK with the S132 Softdevice and the...
I'm having issues with slow directed advertising. I'm having a BLE peripheral where I want the device to advertise (direct) upon disconnects. I initialize the advertising...
My project goal is the following: To get data over USB and sending it to a computer using Bluetooth 5.
I've been looking around for a Bluetooth 5 dongle, but have not found...
I'm trying to sample ADC signal using 12 bit ADC resolution, but the digital signal doesn't match the original one seen in the Oscilloscope.
Here are my ADC configurations...
