I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Hello,
I have developed my own iOS app which is capable of DFU update different devices with nRF51 and nRF52 chips.
Using only APP file (both .hex and .zip) works perfectly...
Hello,
I' trying to switch from keil uVision to Eclipse, but it doesn't work as intended. I can't debug them (hrs with and with out dfu), but the Blinky example works...
Hi,
I'm working on a custom application using two microcontrollers a pic32 and a nrf52832, I require the pic32 using an external flash memory to read the binary file stored...
I'm interesting in knowing a little more about the "address match" output of the nRF905 chip. What is the expected jitter related to the actual radio signal?
E.g. If I...
Using softdevice s132, nRF52832 on a custom board
I don't quite understand how does the SPI work exactly?
I am using it on a battery powered low power sensor application...
Hi,
We are unable to run testing with Nordic nRF52840 preview DK boaed as it is not able to be put into DTM for RF-PHY testing.
I need the hex file to flash and the...
In the nrf52 specification:
"The Phase A, Phase B, and LED signals are mapped to physical pins according to the configuration
specified in the PSEL.A, PSEL.B, and PSEL...
Hello Everyboby,
I want to know how to configure can use Public address for advertising when using nRF connect APP? Now, I just can use Random address for advertising...
Hi,
for production purposes, we need to define the components of our circuit. Less specific definitions of the parts are prefered to ensure the interchangeability of common...
Hello is it possible to send message from nrf52840 to nfr24L01, I tried (pca10056 as transmitter), program is esb_ptx_pca10056 and nrf24L01 as receiver, but could not receive...
Hi,
I would like to create a DFU package for updating an application config flash page.
We have a device where the device reads some configurations from a specific flash...
Hi Team,
Scenario-1:
There is a use-case where 8 to 10 peripheral devices need to be connected with the HUB which is based on nRF52810 and a mobile device should be...
I'm working with nRF52840 on a battery powered device , as a result theres a constraint in the total power of the cell . Now , it's been decided to use the USB2.0 at full...
Hello,
I have a problem with communicating with SD cards ( https://devzone.nordicsemi.com/f/nordic-q-a/34401/fatfs-example-does-not-work-with-every-sd-card ). I resloved...
Occasionally, the NRF_LOG output just keep putting out random old log data. I have enabled the timestamp so I know they are old data. Once it happens, it just stuck in an...
