Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi
i downloaded nordic thingy52 FW and i uploaded on my board PCA20020
and that is working correctly but when a i downloaded nRF5_SDK_15.0.0 at first i compile (ble_app_beacon...
Dear Nordic,
i am just testing ble examples in nrf 52840 dongle and also implementing one uart for just testing
TX pin - 1.10
RX pin - 1.13
transmission works fine...
Hi,
I'm referring to -
1. Custom HID over GATT device
2. nRF51422 HID example modification
So for now, I just used the descriptor mentioned in above links. But "hello...
Hello,
The softdevice S132_SDS_v4.1 spécification write that supports 20 connections at the same time.
I would like to know if it's possible to have 1 central and 20 peripherals...
I'm attempting to make cli application to load from after the softdevice and based on a command enable/disable the BLE functionality. Is there any simple way to do this? Are...
Hi,
I am currently trying to use PCA10001 board as master and slave at the same time. Trying to send data from master(SPI0) and receive it using slave (SPIS1).
I have set...
Hi,
Is exist a tool like nRFutil to make DFU from windows with standard BLE ?
I have found this: https://github.com/NordicSemiconductor/pc-ble-driver but I thing it's...
I'm trying to filter devices by first provisioning a device then checking the composition data for vendor ID,etc... It is a real pain that all that data is only available...
Hi folks, I am trying to talk to the nRF241L from a PIC 16F688. It is my first time with SPI, and to complicate matters I code in assembly only so cannot refer to online examples...
Hi,
We are trying to have control on firmware update of our BLE mesh network. As a starting point I have ran the light-switch examples and DFU over mesh example. In light...
We are develop one product, it is power by four AA battery. It works fine. but now I found a problem. when I power off and then power on again, sometime it can not be reset...
when I start ADC the current will be HIGH .even I UN-Initialization it .
what I have done like that below；
before I started it The current is 0.6ma
but when I start...
I'm trying to communicate with a device over UART, and I'd like to return the response to my commands back to the function the transmission came from.
For example, I want...
I want to develop nrf52840 with ble mesh topology.
However I need one node to transmit data received from all the nodes via uart to a gsm module
Can anyone please tell...
