Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I am working for Adafruit on the bootloader for the upcoming feather nRF52840. Currently testing using the nrf52840DK pc10056. Everything is OK with S140 6.0.0 . Today...
I need to implement a 4kHz signal to drive a buzzer on a custom board of nRF51822 with external 16MHz and 32kHz crystal.
I am using Timer1+PPI+GPIOTE to generate this 4kHz...
I'm currently using:
- Board: NRF52840
- SDK for Mesh 2.1.1
- SDK for Thread and Zigbee v1.0.0
My problem is that I want to merge and run both Bluetooth Low Energy...
Hi, I am using nRF SDK 12.0.0_12f24da, with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c
Initially I was working on integrating...
Hi, I am using nRF52840-DK; Window 10; Embedded Studio and try to run sample project:C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\peripheral\ uart \pca10056\blank\ses ...
Hi all, I'm using nrf52832 with SDK15 in my project. For debugging purposes I need both CLI and LOG modules enabled with RTT as a transport. I followed this manual to setup...
How can I disable NRFX_LOG_INFO calls in the PPI driver? I've set NRFX_PPI_CONFIG_LOG_ENABLED 0 and even NRFX_PPI_CONFIG_LOG_LEVEL 0 but that doesn't stop messages like the...
Hi,
This is Srivisakh. I am using a custom made board integrated with nrf52832 board in which UART is configured. I am using Segger IDE for code development and building...
Hello I have what I hope is a simple question regarding the Internal DC/DC on the nRF52832 and thus nRF52810. I am assuming it is the same internal design, correct between...
We are just in the very beginning of developing a mesh network with 150 devices and a gateway (with a nRF52840 in it). We want to find the best strategy for provisioning....
Hi everyone,
thanks for this discussion - this question addresses almost exactly a potential use case I've been looking into.
I'd like to try and implement something this...
This is from the documentation:
[in,out]
p_length
Pointer Length of the string. Amount of sent bytes.
I'd translate it to a pointer to the requested length...
Hello all, I already did some research finding similar questions and answers in this board, unfortunately I still do not have answer, maybe some can can help pls?
I have...
