Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi Everyone,
Pardon me if i write some illogical stuff. Complete beginner to this microcontroller.
I started using nrf52832 with Zephyr OS . I was trying to configure...
Hi,
I wished to test multiprotocol with one software but I was wondering if it was possible to compile an application which could switch between zigbee and Thread (and...
I'm using arm-none-eabi-gcc 7.2.1 with nRF5_SDK_15.0.0_a53641a with soft device s140_nrf52_6.0.0_softdevice.hex I'm trying to modify one of the bluetooth examples to add a...
Dear Sir,
I use nrf5_SDK_for_Mesh_v2.0.1_src.zip and test proxy server project,
I scanned the device nRF5x Mesh Light (0x1827 Service), I click "Discover services",...
Hi guys
I am trying to program a nrf51822 module but it is not recognized by the development kit.
These are the pins that I am using:
I can not see the...
Hi,
I am using nrf SDK version 12.2.0
The following code fails to produce event for twi transfer complete const nrf_drv_twi_config_t config = { .scl = I2C2_SCL_PIN,...
I'm using the P20 connectors in nRF52 PDK to flash my custom nRF52832 board.
The connections are like this:
SWDIO ----> SWDIO
SWDCLK ---->SWDCLK
VTG ------> VDD
...
Hello,
We have an application with a S132 device, SDK 14 and Softdevice v5.0.0. On some devices, an assert is being thrown in the sleep prepare function. This is the line...
There are errors on Thingy52 "ble_app_thingee_s132_pca20020.emProject" which I built on SEGGER Studio for ARM V3.34 (64-bit) running on Windows 10. Please advise. Thanks....
Hi!
I'm using an NRF51822 as a GATT client to write data to a characteristic. The peripheral responds with several 20 byte indications. When I receive the indications, the...
Hi, I am importing a bootloader project that uses softdevice s110 and NRF51822 from Keil to Segger Embedded Studio. I have got all kind of errors during the process and I...
Hi Team,
In BLE5,
1) Can we connect a peripheral device to multiple central device?
2) Is it possible to check if connecton fails with any central device in perpheral...
I'm trying to put thingy_sdk_v2.1.0 and 10 nrf52832 boards. I'm compiling "ble_app_thingee_s132_pca20020.emProject". I don't know why it's always an error. How do I demonstrate...
Hi,
I'm using nRF52832 and SDK 15 and IDE im using is Segger studio.
i have ported the uart code into Ble_app_multilink_central.When i debug the code it is getting stuck...
Looking for an example on how to advertise for 10 seconds then go into sd_power_system_off. Trying this by using ble_app_template (s112, ses, sdk15.0, custom, 1 led, 1 rgb...
