void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,Sir:
I am developing a 52840’s project using SDK15.1,My development environment is Segger embedded (version 3.34a).When I added the RNG function to the code (the correct...
Hi,
Have an issue with a prototype 2 layer 52840 pcb that i tried to get manufactured. i increased the pad diameter to 0.3mm and now i cannot route without hitting clearance...
Hi
when trying https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library everything goes OK (I think...) all the nodes gets provisioned, all the elements gets addresses...
I know the PDK design is available for download, but there are a lot of things on that board which would not be required for a minimal e.g. beacon design
I'm looking for...
We are looking at developing a proprietary protocol using the nRF52832/40 and were interested in the specific and practical differences between the Ble_2Mbit vs Nrf_2Mbit...
We try to implement DFU over UART. The Mesh DFU example has been taken as a reference. DFU is successful, but it takes about 1 hour (sic!) to transfer DFU ZIP package of size...
Hi,
We are developing a device which should have a power save mode where no BLE connection is possible (switch off the BLE to a minimum power consumption) and restart the...
Hi, there~~ Just noticed that there are codes for the Android nRF connect.
github.com/.../Android-nRF-Connect
Using that code, I wish to create my personal sniffer that...
Good afternoon,
I'm using nRF52840 with SDK15 and Softdevice6.0.0.
I'm using the Queued Write Service Module to make use of a characteristic able to receive up to 510bytes...
Please suggest a tool that can be used for monitoring and and analysis of Nordic's BLE packet transmission rate.
I would like to measure packet irregularities over time...
HI,
How to use sd_ble_opt_set() with the option BLE_GAP_OPT_SCAN_REQ_REPORT ? After setting this I can expect to get the event "BLE_GAP_EVT_SCAN_REQ_REPORT" with information...
Hi,Support Team
I Use the nRF51822 SOC for SDK12.3-example-DFU-bootloader_secure, when I Select the ZIP upadate file,it has a reminder "Loading file has failed. Try different...
Hi,
I use buttonless DFU with the secure bootloader.
When I push a button my application advertise in fast mode with an interval of 40ms and for 5s. After it return to...
