I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear Nordic,
i am just testing ble examples in nrf 52840 dongle and also implementing one uart for just testing
TX pin - 1.10
RX pin - 1.13
transmission works fine...
Hi,
I'm referring to -
1. Custom HID over GATT device
2. nRF51422 HID example modification
So for now, I just used the descriptor mentioned in above links. But "hello...
Hello,
The softdevice S132_SDS_v4.1 spécification write that supports 20 connections at the same time.
I would like to know if it's possible to have 1 central and 20 peripherals...
I'm attempting to make cli application to load from after the softdevice and based on a command enable/disable the BLE functionality. Is there any simple way to do this? Are...
Hi,
I am currently trying to use PCA10001 board as master and slave at the same time. Trying to send data from master(SPI0) and receive it using slave (SPIS1).
I have set...
Hi,
Is exist a tool like nRFutil to make DFU from windows with standard BLE ?
I have found this: https://github.com/NordicSemiconductor/pc-ble-driver but I thing it's...
I'm trying to filter devices by first provisioning a device then checking the composition data for vendor ID,etc... It is a real pain that all that data is only available...
Hi folks, I am trying to talk to the nRF241L from a PIC 16F688. It is my first time with SPI, and to complicate matters I code in assembly only so cannot refer to online examples...
Hi,
We are trying to have control on firmware update of our BLE mesh network. As a starting point I have ran the light-switch examples and DFU over mesh example. In light...
We are develop one product, it is power by four AA battery. It works fine. but now I found a problem. when I power off and then power on again, sometime it can not be reset...
when I start ADC the current will be HIGH .even I UN-Initialization it .
what I have done like that below；
before I started it The current is 0.6ma
but when I start...
I'm trying to communicate with a device over UART, and I'd like to return the response to my commands back to the function the transmission came from.
For example, I want...
I want to develop nrf52840 with ble mesh topology.
However I need one node to transmit data received from all the nodes via uart to a gsm module
Can anyone please tell...
Hello Nordic experts,
I am trying to use app_usbd_ep_enable and app_usbd_ep_disable in order to enable/disable an endpoint. I need this to fake usb unplug/re-plug. Currently...
