Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I am trying to change the mac address of my device every time I advertise a packet. I have a callback on_ble_radio_active_evt where I update the address like this:
...
(I'm developing a firmware on nRF52832, but had actually stareted on nRF51822 and observed the same issue, SDK 12, pending migration to SDK 15)
When my app starts, I output...
Hi all,
I am investigating different protocols to support a network of very low-power Devices and Hosts. The Devices are mostly static (i.e. they don't move around very...
Dear developers,
I am developing a scheme where the nRF51 (central role) connects to iOS device (peripheral roles). The nRF51 connects, performs the discovery procedure and...
Hi,
I developed an application on the nRF51 Dongle (PCA10031) and am now trying to port it to this module. It is a nRF51822 AA device (256K Flash, 16K RAM), and it is Rev...
Hello everyone, I'm currently working on a project and I'm encountering issues.
The project involves with a BLE and a smartphone. The goal is to send Data from an application...
Hi
I have successfully(?) altered my application from using BLE_GAP_PHY_1MBPS to BLE_GAP_PHY_CODED. But how can I test it?
Prior to the modifications I tested the application...
Hello.
I'm trying to add encryption to the secure DFU bootloader. I'm using SDK v15. I know this topic has been discussed on this forum before. In particular I have found...
On NRF52840 DK, I don't have a softdevice installed. I want to do DFU with s140 softdevice only update. But it gives the following error:
raise NordicSemiException('Extended...
Hi,
I got a problem that doing the DFU through buttonless example, but successfully upgrade only in bootloader.
I used OPPO R9s (Android 6) with my personal cell phone...
which pin to use for TWI method communication, in board type 10040 nfr52832 model Taiyo Yuden EKSHJN
in file 10040 I have this definition of pins: what should i change...
Hello:
I have been at this problem for days now and not getting anywhere to a solution. My app is using a static passkey for encryption and does timeout after 30 seconds...
Hi,
I'm experimenting with incorporating " ATT_MTU Throughput" Example into our project.
I'm using nRF52832 as the peripheral and a SDK52 as the central.
The central...
Hi Everyone
I am trying to achieve the following objective
I want to upload the hex file of my application code which blinks leds after 1 second without using th SWD interface...
Hi,
I have my application working on NRF SDK11 on NRF52832 with softdevice 2.0. I am porting the application to SDK 14 and SD 5.0. I am facing APP_UART_COMMUNICATION_ERROR...
