Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
HI,
Under nRF5_SDK_12.2.0_f012efa, with s132_nrf52_3.0.0_softdevice, run on system on low power mode.
I define an app_timer,below is my parameter
APP_TIMER_DEF(m_second_id...
Dear Nordic community
(SDK v14.2, nRF52832)
I have a real-time application where I am sending 6 packet of 20 byte Notification per connection interval. And there is not...
Hi,
When debugging with sdk_15.0.0 ble_app_butonless_dfu project(application project) + secure bootloader project(bootloader project),it will cost about 2~3 minutes for...
Hi,
I am trying to modify the multilink central example to send string to other board.
In the main.c I inserted the uart_init(), uart_event_handle() methods
I added...
Hi everybody,
I'm developing an product with :
NRF52840, V0.9.0, SDK15
In the DK I connected LIS3DH (accelerometer by TWI)
all works.I configuration of HZ and temperature...
Dear Nordic team,
I want to add DFU services to an existing application which is based on ble_app_uart example.( SDK 15.0.0, softdevice S132 6.0.0)
What I have done is...
Im working on merging blinky_c with light_switch_server. Took the blinky example as starting point then merge the mesh code accorging the Coexistence with nRF5 SDK BLE functionality...
The issue is that I fixed some of your bugs in the attached file, as follows:
Changed to handle larger number of records greater than 256 records, we need 500 records...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hello
Im trying to send a small array with two integers over bluetooth mesh
but Im getting error code 7 invalid params..
how should I send an array like this?...
Hi,
I am working on PB Remote example. I would like to be able to run remote scan on my 5 servers immediately after they are provisioned.
For example, I provision the...
I have been using nRF Connect on a Samsung phone for a couple of months, and have forgotten how to install it. My daughter was playing with the phone and managed a factory...
I'm working on a BLE design for nRF52832, with SoftDevice S132 v5.0.0. The project uses FreeRTOS with Tickless Idle enabled. When the user powers the device off (from a UI...
Good morning,
I've inherited a line of nRF51822-powered products that are currently running firmware based on SDK10 and SD130 v1.0.0. UICR-> BOOTLOADERADDR is set to 0x3b000...
After switching from the Blinky example to another project, the BLE services have not been cleared from the Blinky project. The newly built UART App example will load, but...
