I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Next week, we have a meeting with our customer to give them an overview on all our BLE solutions (they are interested in module) but I also want to give them an overview on...
nrf52832, SDK 15.0.0
I develop the project based on the example 'ble_app_buttonless_dfu'
But when I want to add some peripherals, such as SAADC, SPI and PPI, and some...
I'm seeing strange corruption in the nrf52840 virtual COM/UART (the one that goes through USB and the JLink interface MCU).
The nrf52840 is running the UART serialization...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip ...
I would like to use the time library to manage multiple times with different timezones in my embedded system.
I have already seen the ble_app_cts_c example and the nrf5...
this is vishal from VVDN tech working as a Hardware design engineer .
In our project we are going to use 10k module of LTE EC25E.
So we need step file from your side ...
Hello,
In ble_app_blinky code,I cant understand this line "#define APP_BLE_OBSERVER_PRIO 3" and what does the value 3 represents here??. Is this value constant or can be...
Hi,
We have been developing our system around nRF52840 and we are now looking closer into the real-time performance of the MCU & SDK. The scenario is simple: a signal ‘YELLOW...
I am trying to add the valid range descriptor to my measurement interval characteristic in the Health Thermometer. This is a necessary step as my measurement interval characteristic...
Hi
I am using the ble_app_blinky's lbs application, as found here in the 14.2 service
C:\Eran\Software\Nordic\Packages\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a...
Hello,
We have an application on Iphone running with our custom service :
uuid : 0000fdF9-0000-1000-8000-00805f9b34fb
and our characteristics :
char-handle 0x16...
Dear Sir, we are developing an application on the nRF52840 kit with SDK 15.0.0. We are using Keil as compiler. In our application we need to receive data from two uart together...
Hi Everyone,
I have two task in which i am receving data from bluetooth and if i receive a particular hex value , i want a task(which is Toggling LED State) to run on...
Hi,
I am trying to to port ble-mesh code (serial example) into ble_app_uart. I am using nrf5_SDK_forMesh_v2.1.1 and nRF5_SDK_15.0.0_a53641a on DK-N52832.
After merging...
