In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I would like to detect if a reset happened due to a brownout or an actual power off.
I tired so far using the GPREGRET and RESETREAS registers. They are useful to detect...
I have an app that works perfectly when run from the debugger, but not when started by HW reset. We use the serial port to communicate to a control processor (STM32) The Nordic...
Hi,
I was trying to test a slot circle antenna with nRF52832 which is well matched to 2.4G~2.48GHz, but it is circular polarized antenna with high directivity.
However...
Hi All!
I use nrf51822 with sd s110 to send data to android phone with sd_ble_gatts_hvx. If sd_ble_gatts_hvx returns NRF_SUCCESS then that packet get to TX buffer. I didn...
With nRF5 SDK v15, the code size became too large for the free version of UV5 , Is there a way to reduce the code size by reducing some array size or commenting something...
Hi There,
I'm stuck with Getting BLE uart working in another example.
I wasn't sure if converting the BLE Uart example into a central/peripheral application would be more...
Hi.
I want to read thingy's sensor data. I'm using nRF52840 DK.
I have tried using ble_app_multi_link_multi_role example, but there are only read button state.
How can...
Hello everyone !!!
I've recently started working with Segger Embedded studio for nfr52840. I want to add a new driver into an existing projects.Let's say GPIOTE
I...
Hello,
Recently i am working on UART application on nRF51822 based product.
In UART application code, there is no option to configure the modulation rate.
So, I would...
Dear friends,
if i adjust the tx power of nRF52832, e.g., by calling sd_ble_gap_tx_power_set(), which phase of the current will be affected in the pic bellow? just the phase...
I am struggling with getting a Secure UART(Serial) DFU operation to function correctly when I attempt to enter the bootloader with a call from my app. I am using the basic...
Hi all,
I am working on interfacing an SD card as well as an OLED Display with my nrf51422 on SDK 12.2.0.
Although, both are on SPI and hence i need to configure them...
Hello,
I'm running the SPIS example from Keil (SDK 15.0), but I want to print out the received as the decimal value instead of as a string. If I change %s to a %d in this...
I cannot access any more my nRF52 DK 10040 with nrfjprog ,indipendently from the command I give.
I use Windows10 nrfjprog command line ,i can see and access JLINK drive...
