Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi, im using nRF 52 DK. I want to interfac mpu6050 by using the example found on this page https://github.com/Martinsbl/nrf5-mpu-examples . I'm particularly using the example...
hi Support Team,
Mesh 2.0
#if GATT_PROXY if (is_provisioned) { proxy_init(); }
Where is proxy_init() declared and defined..
I am not able to goto definition by RightClick...
We need to measure a pulse width and create an event when it changes. The change will be from 10 to 80 percent, roughly - 1mS to 8mS or more. This is a very loose requirement...
Hi
I have to combine both BLE UART profile and RTC examples of nrf52 of 11.0.0 SDK for my application.When I run them individually, they are working fine.After combining...
Hello,
I am working with nRF52832 and using Keil uVISION 5.
While building the exapmple from nRF SDK v15, I am getting this error :
error: L6236E: No section matches...
Hi, I have nrf52832 and using QDEC driver. In my application I want to use values accumulated in the acc/accread register for a time of the order of seconds. Since max value...
Hi all, I found one issue with my custom nrf51422ble board. When I use my office PC and KEIL IDE, my custom board BLE is working but when I use my home PC KEIL, it's not working...
Hi, I am using https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo with segger embedded studio and nordic thingy52 modules. I have problem with the mesh assert which...
Hi,
I'm new to this product and I'm facing some problems in dowloading the required softwares to program the nRF52 DK, I saw most of the tutorials here and they are old...
I was trying to upload one of the examples which is ble_app_hrs file to test nRF52 DK. However, it gives me a message that i have about 31 errors.
Below are some types...
Hello Everyone,
I am an experienced engineer but actually a beginner with Bluetooth technology. I am working on a project that uses a Fanstel BT832AF Bluetooth module. This...
Hi,
I need to be able to put larger strings in the scheduler. At the moment the maximum accepted values for init are the following:
#define SCHED_MAX_EVENT_DATA_SIZE...
Hi, I am confused by this config.
static void drv_keyboard_gpio_init(void) { // Make sure that columns will drive 0 when they will be configured as outputs. NRF_GPIO->OUTCLR...
I'm using a NRF52840 with S140 softdevice. I advertise some data and I want to be notified when advertising start. I followed this thread and I use the customs ble_radio_notification...