Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I'm developing an nRF52 application based on SDK14 and S132 that require the DFU service.
The DFU is not performed using the nRF toolbox application on both of android...
I have recently installed Segger Embedded Studio (v3.30) and have installed the CMSIS package (v4.5 I think) and have modified the tools.xml as demonstrated in the Nordic...
hi all,
how to use Atomic FIFO Lib on ble stack ?
Called nrf_atfifo_get_free() always get NRF_ERROR_NOT_FOUND when ble_peripheral connect to central .
In ble_app_uart...
It is very easy to build the example applications in the nRF mesh SDK (v2.2.0), but what is the official way to structure the build system when developing an application with...
I am working with a ublox NINA-B1 based board. NINA-B1 uses the nRF52832. IDE is Segger. I followed the ublox instructions to create a custom board matching NINA based on...
What are the steps to be carried out for setting mesh network
I have flashed client hex file in one nRF52840 dongle and server hex file on other dongle. The example I am...
Hi!
I may have asked about this earlier in a lengthy question:
https://devzone.nordicsemi.com/f/nordic-q-a/35576/low-power-remote-control
But I'd like to be sure about...
(note - my core problem is that I'm trying to compile a file that's larger than 32KB, so I can't use uVision - if there is an easier way to circumvent this then I don't really...
I inherited a Nordic Semi firmware project. It was developed using s132_nrf52_4.0.2softdevice.hex and SDK 13.1.0.
How can I download these versions? I would like to start...
I installed the nRF5_SDK_15.1.0 compiled and ran the ble_app_att_mtu-throughput example.
The first run was using the default settings all went as expected. For the second...
Hello Nordic team,
I am working on ble_peripheral example. Initially application binary file size is 100 KB but after adding support of FDS application size increased to...
Hello,
I have read through all the posts I can find on this subject, but none has solved my problem.
- nRF5_SDK_15.1.0
- Example: Segger Embedded Studio Project: twi_master_with_twis_slave_pca10040...
I want to fully understand the use of RTOS in conjunction with the stack. As an example, I took an example ble_app_hrs_freertos (SDK v15.0).
Add a service, for example...
I need to count the pluse number use 51822, the frequency about this pluse is about 0.01Hz to 1Hz and is not fixed, I know use Time1 can achieve this funtion, but the problem...
