Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
I have tested AES-CCM of nRF52832 with reference to the following answered questions.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
devzone.nordicsemi...
Dear all,
I did below steps to connect to the BluFruit Feather board via STLink V2:
1) Install OpenOcd and STLink USB driver as: https://pcbreflux.blogspot.com/2016...
I have some code originally working using SDK 13. It reads data from the UART and send it out in scan responses. iOS was able to capture the scan response data successfully...
hi all,
Our application is a peripheral device with sensor data that is sending up to 540kb/s (68kB/s) to the central device (data rate could probably be reduced if necessary...
Hi,
I'm trying to take the readings of temperature and humidity from 4 Nordic Thingy:52 sensors by using mesh. I did the connection of the mesh and I can control the nodes...
Hello,
I am new to BLE so I am not sure where to start. I have two nRF52832 chips, one will receive data from an FPGA through SPI and then I want to send the data to the...
For reference, in case anyone else gets a similar issue :
Using the SES import facility to import a Keil MDK v5.25 Project.
After fixing a couple of other import errors...
Hi @ll,
I'm not able to receive any ble events that should be triggered by the SoftDevice.
What I did: - Using dfu_example (added beaconing advertiser and connectable...
hi,
I use SR3 52 V1.2 for development, and I want to copy a new project to change some code.
When I changed the file name, I found it could not be compiled through, only...
Hi all,
We are currently developing a wireless system for a musical instrument and MIDI controller based on a nRF52832 (using Laird BL652 modules). Our requirements prevents...
Hi,
I would like to test the ZigBee throughput like the examples ("ATT_MTU Throughput Example" for BLE and "Thread Throughput Measurement Application").
I'm not familiar...
Dear Support,
I am working with the new SDK 15, and got some question about using whitelist without device manager, and without pairing or bonding. As stated here: https...
I'm using v14 of the SDK and I cannot for the life of me get either the external 32MHz or 32.768kHz clocks working.
How is this possible using the SDK?
Our company is manufacturing security and telecom products. In our security product range, we are adding blue tooth based product which is under development. For this product...
