Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi, I am building a system using Nordic NRF52832 as a node. I would like to save some data (such as node ID) to board's memory so that the application can read these data...
Hello, i am developer for nrf51822, Please, have you tried to connect bluetooth nrf51822 with samsung s8 plus ?? because I noticed that sometimes it connects and disconnects...
I want to use the MPU9250 driver found in the Thingy SDK in my nRF52 project. I am using GCC 7.2 Arm/Eclipse as the development environment. The driver source file inv_mpu_dmp_motion_driver...
I would like to implement feature that swaps advertising data only if GAP address in scan request matches one of the application layer ,,authorized'' addresses.
The only...
Hi,
My app was written on Windows PC/MSVC and is ported to nRF52/Keil.
In many places I've used MSVC assert() macro in the following manners:
assert(function(arg1...
Hi all,
On SDK 15.0, Immediate Alert Service is not working without a secured BLE link. When peripheral is not paired, this latter doesn't receive any alert from central...
I’m using SDK 15.0.0. and softdevice 6.0.0.
When I compile the example:
https://github.com/haakonsh/MMD
I get the compiler error:
fatal error: compiler_abstraction...
Hi,
I tried ble_app_uart example by using SES it works fine. Then I tried it by using eclipse with OpenOCD and a STlink V2 on the debug in port I succeeded to flash it....
Hey guys,
With the new SDK15, I find myself looking at dependency problems over and over again. Right now, I am trying to setup a simple A/D conversion using nrfx_adc. Found...
Hi Env: keil uvision 5 and SDK 9 and custome breakoutboard for nRF51822 (PTR5518: no external crystal) and no SD.
I am trying doing the first steps in twi over nRF51822...
I been reading over your entire tutorials, but I have yet to see any tutorials that guides me towards creating an NRF52 project from scratch? Could anyone guide me through...
Hi,
I am transferring my nrf52832 project to nrf52810,and I have deploy the project according to the user guide (Transferring the project to nRF52810 hardware),
when I...
Hello everyone,
I'm developing an application for boards with NRF52832, Softdevice S132 3.00 and SDK 12.3.0.
The network architecture consists of:
one peripheral board...
I'm using my accelerometer's GPIO interrupt to wake up the MPU from PowerOFF mode and it works great. Now, I'm trying to use the same interrupts to wake it up from Sleep mode...
Hi,
I have migrated from SDK14.1 to SDK15.
One thing is embarrassing me.
I would like to modify the scan data as above, I do not know where I can fix it.
phy...
