The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Is there any method to remove a single node from the network in current mesh SDK 2.1.0 with s132 soft-device 6.0?
With "config_client_node_reset" it will remove all the...
I am using the Thread Border Router 1.0.0 on a Raspberry Pi 3B+
I have not been able to connect the RaspPi to our wifi network.
I tried this method first, as described...
Hi,
I'm using the nRF52840 dongle. Using nRF Connect v2.5.0 - Programmer (experimental) tool, I've downloaded the following hex files:
softdevice_s140.hex,
ble_app_buttonless_dfu_with_bonds_s140_with_setting_page...
Hi.
I am adding buzzer beeping in Immediate Alert Service of ble_app_proximity example. Event thought Immediate Alert signal is sent from nRF Master Control, there is no...
Hi I saw example with other product like the thingy.
Do you already created app creating link with the thingy microphone and the integrated speaker, it could be nice.
...
I'm exploring an nRF51 DK board I bought using openOCD (on circuit debugger), eclipse, and the gcc/gdb toolchain under Linux.
I'm trying to understand the chip by hand probing...
I make a custom board with nRF52832, the nRFgo Studio can find the device before I download anything, then I down do erase all and download the softdevice132, after this I...
I'm working with S132, SDK15.0 and an NRF52832 defining custom services.
I have two services with each with several characteristics. I need to be able to determine which...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK. I want to use nrf51 as SPI slave and other MCU as SPI master. I am using spis_pca10028 as example.
...
I'm try to sending command to our device for using ble_nus_c_string_send function, but there has a problem when I addition 0x00 value in data the client can't receive any...
Reviewing the PCA63511_Schematic. On Sheet 2, looking at the nRF52832 chip
(1) What is PO.05 used for? It controls the BJTs (Q1A, Q1B and Q2A) which clamps the input to...
Hi,
We have a board with a nRF8001 running with a STM32F4 as device role.
The bluetooth profile is Nordic UART.
We successfully connect and exchange data with Linux...
