I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello Devzone,
I've been using nRF52810, SoftDevice 112 (5.1.1), for a Mic recording application. What I'm trying to do is sample PDM MEMS mic data through PDM interface...
Dear Team,
I have nRF52 DK and nRF52840 DK, Can we program nRF9160 using nRF52 DK?
Please let me know the process and detailed wiring to program nRF9160.
Ashiq Moha...
Hi,
Good Day!
Statement of Problem: We use Li-Ion Battery in our application and would like to monitor a few variables such as Battery Voltage, Battery temperature & Discharge...
Hello, I'm trying to set up SPI communication with a sensor from my nrf5284_pca10056 running zephyr.
This is my prj.conf file:
This is my .overlay file:
And this...
I'm looking at the GPIO functions in http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/reference/peripherals/gpio.html , and looking at the function prototype...
Hi
I'm have and NRF52840 with a MPU9250 connected via TWI. The connection to the MPU9250 is successful, I can find its address on the bus (0x68).
I've implemented a very...
I am trying to add to an existing project gpiote
I have copied the code from the example project and tried to add all the files and changes to my sdk_config.h to match the...
Hello all,
I'm trying to develop a basic bike computer, compatible with ANT+. For that, I'm using nRF52 DK. My main objective is to be able to connect to any commercial...
Hello,
I have nRF52840 with code that is based on SDK16.
I am not using Softdevice in my project - just MBR , Bootloader and Application.
I was able to upgrade my code...
Hi all,
We are successfully using the nRF52840 chip in one of our projects except for the DFU functionality. We tried following these tutorials without success:
devzone...
Hi, I'm dealing with the ble long_range_demo. Central packet gives arrival time and rssi signal through the rtt viewer. However, I am willing to know the sending time of the...
Hi all,
I am investigating Mesh SDK and interoperability between devices.
We have bought some Hytronik devices which are qualified with Bluetooth.
Strange thing is that...
Hi,
I am new to thread network. In my application only a few nodes, mostly one. How can I connect this one node to the internet? Assume WiFi is available.Can I use the thread...
